FIND YOUR REMOTE

Find your remote and compatable JMA Remote to copy

Legend: Click on the symbols for further information

Frequency

Type of code

  1. Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
  2. Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.

Buttons

Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.

PROCESS:

  1. In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
  2. Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.

If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.

Copy

No copy

FOR: OPEN OUT® AU1600

  • F 433,92
  • C ROLLING CODE
  • B 2
  • AP YES
  • BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
OPEN OUT® AU1600

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING GIBIDI ROLLING CODE REMOTE CONTROLS

Direct synchronisation procedure on the receiver

1. Open the receiver and locate the programming button on the circuit board.

2. Press it briefly.

The receiver LED will flash.

3. Within 10 seconds, press the button of the remote control you wish to synchronise.

The receiver will automatically exit synchronisation mode after a short time.

FOR: OPEN OUT® AU1600 WOOD

  • F 433,92
  • C ROLLING CODE
  • B 2
  • AP YES
  • BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
OPEN OUT® AU1600 WOOD

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING GIBIDI ROLLING CODE REMOTE CONTROLS

Direct synchronisation procedure on the receiver

1. Open the receiver and locate the programming button on the circuit board.

2. Press it briefly.

The receiver LED will flash.

3. Within 10 seconds, press the button of the remote control you wish to synchronise.

The receiver will automatically exit synchronisation mode after a short time.

FOR: OPEN OUT® AU1680

  • F 433,92
  • C ROLLING CODE
  • B 2,4
  • AP YES
  • BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
OPEN OUT® AU1680

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING GIBIDI ROLLING CODE REMOTE CONTROLS

Direct synchronisation procedure on the receiver

1. Open the receiver and locate the programming button on the circuit board.

2. Press it briefly.

The receiver LED will flash.

3. Within 10 seconds, press the button of the remote control you wish to synchronise.

The receiver will automatically exit synchronisation mode after a short time.

FOR: OPEN OUT® AU1680 WOOD

  • F 433,92
  • C ROLLING CODE
  • B 2,4
  • AP YES
  • BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
OPEN OUT® AU1680 WOOD

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING GIBIDI ROLLING CODE REMOTE CONTROLS

Direct synchronisation procedure on the receiver

1. Open the receiver and locate the programming button on the circuit board.

2. Press it briefly.

The receiver LED will flash.

3. Within 10 seconds, press the button of the remote control you wish to synchronise.

The receiver will automatically exit synchronisation mode after a short time.

FOR: OPEN OUT® DOMINO

  • F 433,92
  • C ROLLING CODE
  • B 4
  • AP YES
  • BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
OPEN OUT® DOMINO

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING GIBIDI ROLLING CODE REMOTE CONTROLS

Direct synchronisation procedure on the receiver

1. Open the receiver and locate the programming button on the circuit board.

2. Press it briefly.

The receiver LED will flash.

3. Within 10 seconds, press the button of the remote control you wish to synchronise.

The receiver will automatically exit synchronisation mode after a short time.

FOR: OPEN OUT® GIBIDI 26,995

  • F 26,995
  • C FIX CODE
  • B 1,2,4
  • AP NO
  • M-Q MAX
OPEN OUT® GIBIDI 26,995

See compatible JMA remotes

FOR: OPEN OUT® L110

  • F 305
  • C FIX CODE
  • B 1
  • AP NO
  • BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
OPEN OUT® L110

See compatible JMA remotes

FOR: OPEN OUT® MTQ 26,995

  • F 26,995
  • C FIX CODE
  • B 2,4
  • AP NO
  • M-Q MAX
OPEN OUT® MTQ 26,995

See compatible JMA remotes

FOR: OPEN OUT® MTQ NEW

  • F 26,995
  • C FIX CODE
  • B 2,4
  • AP NO
  • M-Q MAX
OPEN OUT® MTQ NEW

See compatible JMA remotes