FIND YOUR REMOTE

Find your remote and compatable JMA Remote to copy

Legend: Click on the symbols for further information

Frequency

Type of code

  1. Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
  2. Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.

Buttons

Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.

PROCESS:

  1. In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
  2. Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.

If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.

Copy

No copy

FAAC® DL868SLH

  • F 868,3
  • C ROLLING CODE
  • B 2,4
  • AP YES
  • M-BT / M-FR1 / SR-48
FAAC® DL868SLH

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING FAAC ROLLING CODE REMOTE CONTROLS

FAAC remote controls can be synchronised using a master remote control with its own code. In this case it is not necessary to work directly or remotely with the receiver.

Follow these steps to synchronise a slave remote control from a master device. This procedure is valid for the TML and 868 SLH series.

TML series

Warning: if you press the slave remote control first and then the master device you will delete the master codes.

1. Press the button of the already synchronised remote control and hold down.

2. Still holding down the master device button, press the same button on the slave with the two devices close to each other.

The LED on the slave will flash.

3. Repeat the operation for the remaining buttons.

SERIE 868SLH

Warning: if you press the slave remote control first and then the master device you will delete the master codes.

1. Press the two buttons on the master device until the LED starts flashing and release after one second (on devices with four buttons, press the top right and lower left buttons).

2. Before the master device LED stops flashing, press the top right button on the master device again with the remote controls close to each other. The master LED will change to steady.

3. Still holding down the master device button, press the same button on the slave.

The slave device LED will flash once to confirm that the code has been stored.

4. Release both buttons.

FAAC® R40 245 ANTIGUO

  • F 245
  • C FIX CODE
  • B 1,2
  • AP NO
  • SR-4V
FAAC® R40 245 ANTIGUO

See compatible JMA remotes

FAAC® R40 245 NUEVO

  • F 245
  • C FIX CODE
  • B 1,2,3
  • AP NO
  • SR-4V
FAAC® R40 245 NUEVO

See compatible JMA remotes

FAAC® R40 330 ANTIGUO

  • F 330
  • C FIX CODE
  • B 1,2
  • AP NO
  • M-BT / M-FR1 / M-SP2 / M-SP1 / SR-4V
FAAC® R40 330 ANTIGUO

See compatible JMA remotes

FAAC® R40 330 NUEVO

  • F 330
  • C FIX CODE
  • B 1,2,3
  • AP NO
  • M-BT / M-FR1 / M-SP2 / M-SP1 / SR-4V
FAAC® R40 330 NUEVO

See compatible JMA remotes

FAAC® T224

  • F 224,7
  • C FIX CODE
  • B 1,2,3
  • AP NO
  • SR-4V
FAAC® T224

See compatible JMA remotes

FAAC® T27

  • F 27,095
  • C FIX CODE
  • B 1,2,3
  • AP NO
  • M-Q +
FAAC® T27

See compatible JMA remotes

FAAC® T31

  • F 30,875
  • C FIX CODE
  • B 1,2,3
  • AP NO
  • M-Q +
FAAC® T31

See compatible JMA remotes

FAAC® T433SLH

  • F 433,92
  • C ROLLING CODE
  • B 2,4
  • AP YES
  • M-BT / M-FR1 / SR-4V / SR-48
FAAC® T433SLH

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING FAAC ROLLING CODE REMOTE CONTROLS

FAAC remote controls can be synchronised using a master remote control with its own code. In this case it is not necessary to work directly or remotely with the receiver.

Follow these steps to synchronise a slave remote control from a master device. This procedure is valid for the TML and 868 SLH series.

TML series

Warning: if you press the slave remote control first and then the master device you will delete the master codes.

1. Press the button of the already synchronised remote control and hold down.

2. Still holding down the master device button, press the same button on the slave with the two devices close to each other.

The LED on the slave will flash.

3. Repeat the operation for the remaining buttons.

SERIE 868SLH

Warning: if you press the slave remote control first and then the master device you will delete the master codes.

1. Press the two buttons on the master device until the LED starts flashing and release after one second (on devices with four buttons, press the top right and lower left buttons).

2. Before the master device LED stops flashing, press the top right button on the master device again with the remote controls close to each other. The master LED will change to steady.

3. Still holding down the master device button, press the same button on the slave.

The slave device LED will flash once to confirm that the code has been stored.

4. Release both buttons.