Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
AVIDSEN® 104250 OLD2 Remote
- F 433,92
- C ROLLING CODE
- B 4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
SYNCHRONISING V2 ROLLING CODE REMOTE CONTROLS
V2 remote controls can be synchronised either remotely or directly on the receiver.
Remote synchronising procedure
1. Press buttons 1 and 2 on the remote control to be synchronised simultaneously for approximately 10 seconds.
2. Release.
3. Within 5 seconds, press any other button on the device to be synchronised.
4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.
The code has been stored.
Since this option is not enabled on all models we recommend the following procedure.
Direct synchronisation procedure on the receiver
1. Open the receiver and locate the small SW1 button.
2. Press until the receiver LED lights up.
3. Within 5 seconds, press the button on the remote control to be synchronised and hold until the receiver LED blinks.
4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.
The code has been stored.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
HORMANN® DH 26995 Remote
TELCOMA® FOX 30 Remote
CARDIN® S438 TX Remote
- F 433,92
- C FIX CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
TAU® 250 TXAH Remote
- F 433,92
- C FIX CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
TAU® 250 T4C Remote
- F 433,92
- C FIX CODE
- B 4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
DOITRAND® MPSTFERJ Remote
- F 433,92
- C FIX CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SOMMER® 4025 433 Remote
- F 433,92
- C ROLLING CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING SOMMER ROLLING CODE REMOTE CONTROLS
SOMMER remote control can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver
1. Press button B on the receiver
a. Once for channel 1. LED (C1) will light up.
b. Twice for channel 2. LED (C2) will light up.
The receiver will exit synchronisation mode if no code is transmitted during a period of 10 seconds.
To exit synchronisation mode, press key B several times until all LEDs have turned off.
2. Press the desired button (D) on the remote control. The transmitter will send the radio code to the receiver.
The LED for the selected channel will flash and switch off.
Repeat Steps 1 and 2 to synchronise additional transmitters with this receiver.
STAGNOLI® KALLISTO Remote
KEY® TXB-42 Remote
- F 433,92
- C FIX CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
KEY® TXG-44R Remote
- F 433,92
- C ROLLING CODE
- B 4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING KEY ROLLING CODE REMOTE CONTROLS
KEY remote controls can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver (type A receiver)
1. Press button S on the receiver.
2. The LED (Ir1) will light up.
3. Release button S and press button P.
4. The LED (Ir1) will flash once.
5. Release the button.
6. Press the button of the remote control to be synchronised until the LED (Ir1) begins to flash, then release.
7. Wait for 10 seconds for the receiver to exit synchronisation mode.
Direct synchronisation procedure on the receiver (type B receiver)
1. Press KEY the same number of times as the channel you wish to synchronise (one time for channel 1, two times for channel 2, etc.).
2. The LED will flash the number of times equal to the number of the selected channel.
3. Within the next 7 seconds, press the button on the remote control to be synchronised for 2 seconds.4. The LED will flash once if synchronisation has been successful.
5. Repeat step 3 if you wish to add more remote controls.
TAU® 250 SLIM Remote
- F 433,92
- C FIX CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
The selected remotes can not be copied with a single JMA remote