Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
WAYNE DALTON® E2PUSH Remote
- F 433,92
- C FIX CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
DOITRAND® MPSTFERE Remote
- F 433,92
- C FIX CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
ROLLTORE® R40 Remote
- F 330
- C FIX CODE
- B 1,2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
SKY MASTER® MHZ Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING SKYMASTER ROLLING CODE REMOTE CONTROLS
SKYMASTER remote controls can only be synchronised directly on the receiver. The process is as follows.
Synchronisation procedure on the receiver
1. Press the CODE button once.
The red LED will begin the flash.
2. Press the button on the remote control to be synchronised twice.
The red LED will change to steady and then turn off.
3. Repeat the operation for every button (channel) and every device you wish to synchronise.
If the remote control being synchronised is the first one, you will have to delete the memory as follows:
1. Press and hold the CODE button for 8 seconds during which the LED will remain steady
2. The red LED will turn of and the memory will be deleted.
KEY® PLAY4R Remote
PROGET® ETY B Remote
ALULUX® RATOR40 Remote
DOITRAND® TSDE Remote
- F 433,92
- C FIX CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
PORTAMATIC® MPSN Remote
- F 289
- C FIX CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
ECOSTAR® 40 Remote
- F 433,92
- C FIX CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
BFT® BRC B Clear ICE Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING BFT ROLLING CODE REMOTE CONTROLS
The receivers of these models enable remote or direct synchronisation.
Remote synchronisation procedure for the BFT MITTO remote control
1. Stand near the receiver and press the hidden button at the rear of the BFT original remote control for 2 seconds.
2. Press the left button on the front of the original remote control for 2 seconds.
3. Press the synch button on the rear of the device to be synchronised.
4. Finally, press the first button on the device to be synchronised.
Remote synchronisation procedure for the BFT TRC or MITTO remote control
1. Open the receiver and locate the SW-1 and SW-2 buttons. Press the first (SW-1).
A flashing LED should light up in the receiver.
2. Open the battery cover of the already synchronised remote control or the one you have copied and press the button inside.
The receiver light should change to steady.
3. Press the button of the device to be synchronised.
The light on the receiver will return to flashing and turn off after 30 seconds, indicating that the synchronisation process has finished.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
MERLIN® 2.0 E945M Remote
MOTORLIFT® 9433E Remote
- F 433,92
- C ROLLING CODE
- B 1,3
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING LIFT MASTER ROLLING CODE REMOTE CONTROLS
The Lift Master remote control can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver
1. Press the button on the remote control and hold.
2. Press and release the Learn button for channel A on the receiver.
3. The control LED will flash once.
4. Release the remote control button.
If you release the remote control button before the control LED flashes the receiver will not accept the code.
Repeat this procedure for any other devices you wish to add.
If you are using a second door, select another button on the remote control and repeat the steps for channel B.
The selected remotes can not be copied with a single JMA remote