FIND YOUR REMOTE

Find your remote and compatable JMA Remote to copy

Legend: Click on the symbols for further information

Frequency

Type of code

  1. Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
  2. Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.

Buttons

Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.

PROCESS:

  1. In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
  2. Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.

If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.

Copy

No copy

FOR: KEY® TXB-42

  • F 433,92
  • C FIX CODE
  • B 2
  • AP NO
  • BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
KEY® TXB-42

See compatible JMA remotes

FOR: KEY® TXB-42N

  • F 433,92
  • C FIX CODE
  • B 2
  • AP NO
  • BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
KEY® TXB-42N

See compatible JMA remotes

FOR: KEY® TXB-42R

  • F 433,92
  • C ROLLING CODE
  • B 2
  • AP NO
  • BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
KEY® TXB-42R

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING KEY ROLLING CODE REMOTE CONTROLS

KEY remote controls can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver (type A receiver)

1. Press button S on the receiver.

2. The LED (Ir1) will light up.

3. Release button S and press button P.

4. The LED (Ir1) will flash once.

5. Release the button.

6. Press the button of the remote control to be synchronised until the LED (Ir1) begins to flash, then release.

7. Wait for 10 seconds for the receiver to exit synchronisation mode.

Direct synchronisation procedure on the receiver (type B receiver)

1. Press KEY the same number of times as the channel you wish to synchronise (one time for channel 1, two times for channel 2, etc.).

2. The LED will flash the number of times equal to the number of the selected channel.

3. Within the next 7 seconds, press the button on the remote control to be synchronised for 2 seconds.4. The LED will flash once if synchronisation has been successful.

5. Repeat step 3 if you wish to add more remote controls.

FOR: KEY® TXB-44R

  • F 433,92
  • C FIX CODE
  • B 4
  • AP NO
  • BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
KEY® TXB-44R

See compatible JMA remotes

FOR: KEY® TXG-44

  • F 433,92
  • C FIX CODE
  • B 4
  • AP NO
  • BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
KEY® TXG-44

See compatible JMA remotes

FOR: KEY® TXG-44R

  • F 433,92
  • C ROLLING CODE
  • B 4
  • AP NO
  • BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
KEY® TXG-44R

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING KEY ROLLING CODE REMOTE CONTROLS

KEY remote controls can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver (type A receiver)

1. Press button S on the receiver.

2. The LED (Ir1) will light up.

3. Release button S and press button P.

4. The LED (Ir1) will flash once.

5. Release the button.

6. Press the button of the remote control to be synchronised until the LED (Ir1) begins to flash, then release.

7. Wait for 10 seconds for the receiver to exit synchronisation mode.

Direct synchronisation procedure on the receiver (type B receiver)

1. Press KEY the same number of times as the channel you wish to synchronise (one time for channel 1, two times for channel 2, etc.).

2. The LED will flash the number of times equal to the number of the selected channel.

3. Within the next 7 seconds, press the button on the remote control to be synchronised for 2 seconds.4. The LED will flash once if synchronisation has been successful.

5. Repeat step 3 if you wish to add more remote controls.

FOR: KEY® TXP-42

  • F 433,92
  • C FIX CODE
  • B 2
  • AP NO
  • BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
KEY® TXP-42

See compatible JMA remotes