FIND YOUR REMOTE

Find your remote and compatable JMA Remote to copy

Legend: Click on the symbols for further information

Frequency

Type of code

  1. Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
  2. Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.

Buttons

Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.

PROCESS:

  1. In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
  2. Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.

If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.

Copy

No copy

FOR: MHOUSE® GTX

  • F 433,92
  • C ROLLING CODE
  • B 4
  • AP YES
  • BT Slim / M-FR1 / M-NOVA / M-BT
MHOUSE® GTX

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING MHOUSE ROLLING CODE REMOTE CONTROLS

MHOUSE remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.

Remote synchronisation procedure (identical to procedure for NICE, Smilo and Flo-R devices)

1. Press and hold the button on the device you wish to synchronise for at least 5 seconds and then release.

2. Slowly press the button on the previously-synchronised remote control 3 times.

3. Slowly press the button on the device to be synchronised once.

Direct synchronisation procedure on the receiver

1. Press button P1 on the receiver and hold for at least 3 seconds.

2. Release the button when LED P1 lights up.

3. You have 10 seconds to press any button on the device to be synchronised for at least 2 seconds. LED P1 will flash 3 times if synchronisation has been performed successfully.

4. If you wish to synchronise additional remote controls, repeat step 2 within 10 seconds or the receiver will automatically exit synchronisation mode.

FOR: MHOUSE® GTXC

  • F 433,92
  • C ROLLING CODE
  • B 4,8
  • AP YES
  • BT Slim / M-FR1 / M-NOVA / M-BT
MHOUSE® GTXC

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING MHOUSE ROLLING CODE REMOTE CONTROLS

MHOUSE remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.

Remote synchronisation procedure (identical to procedure for NICE, Smilo and Flo-R devices)

1. Press and hold the button on the device you wish to synchronise for at least 5 seconds and then release.

2. Slowly press the button on the previously-synchronised remote control 3 times.

3. Slowly press the button on the device to be synchronised once.

Direct synchronisation procedure on the receiver

1. Press button P1 on the receiver and hold for at least 3 seconds.

2. Release the button when LED P1 lights up.

3. You have 10 seconds to press any button on the device to be synchronised for at least 2 seconds. LED P1 will flash 3 times if synchronisation has been performed successfully.

4. If you wish to synchronise additional remote controls, repeat step 2 within 10 seconds or the receiver will automatically exit synchronisation mode.

FOR: MHOUSE® MOOVO

  • F 433,92
  • C ROLLING CODE
  • B 4
  • AP YES
  • BT Slim / M-FR1 / M-NOVA / M-BT
MHOUSE® MOOVO

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING MHOUSE ROLLING CODE REMOTE CONTROLS

MHOUSE remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.

Remote synchronisation procedure (identical to procedure for NICE, Smilo and Flo-R devices)

1. Press and hold the button on the device you wish to synchronise for at least 5 seconds and then release.

2. Slowly press the button on the previously-synchronised remote control 3 times.

3. Slowly press the button on the device to be synchronised once.

Direct synchronisation procedure on the receiver

1. Press button P1 on the receiver and hold for at least 3 seconds.

2. Release the button when LED P1 lights up.

3. You have 10 seconds to press any button on the device to be synchronised for at least 2 seconds. LED P1 will flash 3 times if synchronisation has been performed successfully.

4. If you wish to synchronise additional remote controls, repeat step 2 within 10 seconds or the receiver will automatically exit synchronisation mode.

FOR: MHOUSE® MOOVO GRIS

  • F 433,92
  • C ROLLING CODE
  • B 4
  • AP YES
  • BT Slim / M-FR1 / M-NOVA / M-BT
MHOUSE® MOOVO GRIS

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING MHOUSE ROLLING CODE REMOTE CONTROLS

MHOUSE remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.

Remote synchronisation procedure (identical to procedure for NICE, Smilo and Flo-R devices)

1. Press and hold the button on the device you wish to synchronise for at least 5 seconds and then release.

2. Slowly press the button on the previously-synchronised remote control 3 times.

3. Slowly press the button on the device to be synchronised once.

Direct synchronisation procedure on the receiver

1. Press button P1 on the receiver and hold for at least 3 seconds.

2. Release the button when LED P1 lights up.

3. You have 10 seconds to press any button on the device to be synchronised for at least 2 seconds. LED P1 will flash 3 times if synchronisation has been performed successfully.

4. If you wish to synchronise additional remote controls, repeat step 2 within 10 seconds or the receiver will automatically exit synchronisation mode.

FOR: MHOUSE® MOOVO VERDE

  • F 433,92
  • C ROLLING CODE
  • B 4
  • AP YES
  • BT Slim / M-FR1 / M-NOVA / M-BT
MHOUSE® MOOVO VERDE

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING MHOUSE ROLLING CODE REMOTE CONTROLS

MHOUSE remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.

Remote synchronisation procedure (identical to procedure for NICE, Smilo and Flo-R devices)

1. Press and hold the button on the device you wish to synchronise for at least 5 seconds and then release.

2. Slowly press the button on the previously-synchronised remote control 3 times.

3. Slowly press the button on the device to be synchronised once.

Direct synchronisation procedure on the receiver

1. Press button P1 on the receiver and hold for at least 3 seconds.

2. Release the button when LED P1 lights up.

3. You have 10 seconds to press any button on the device to be synchronised for at least 2 seconds. LED P1 will flash 3 times if synchronisation has been performed successfully.

4. If you wish to synchronise additional remote controls, repeat step 2 within 10 seconds or the receiver will automatically exit synchronisation mode.

FOR: MHOUSE® RT3

  • F 433,92
  • C ROLLING CODE
  • B 3
  • AP YES
  • BT Slim / M-FR1 / M-NOVA / M-BT
MHOUSE® RT3

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING MHOUSE ROLLING CODE REMOTE CONTROLS

MHOUSE remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.

Remote synchronisation procedure (identical to procedure for NICE, Smilo and Flo-R devices)

1. Press and hold the button on the device you wish to synchronise for at least 5 seconds and then release.

2. Slowly press the button on the previously-synchronised remote control 3 times.

3. Slowly press the button on the device to be synchronised once.

Direct synchronisation procedure on the receiver

1. Press button P1 on the receiver and hold for at least 3 seconds.

2. Release the button when LED P1 lights up.

3. You have 10 seconds to press any button on the device to be synchronised for at least 2 seconds. LED P1 will flash 3 times if synchronisation has been performed successfully.

4. If you wish to synchronise additional remote controls, repeat step 2 within 10 seconds or the receiver will automatically exit synchronisation mode.

FOR: MHOUSE® TX4

  • F 433,92
  • C ROLLING CODE
  • B 4
  • AP YES
  • BT Slim / M-FR1 / M-NOVA / M-BT
MHOUSE® TX4

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING MHOUSE ROLLING CODE REMOTE CONTROLS

MHOUSE remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.

Remote synchronisation procedure (identical to procedure for NICE, Smilo and Flo-R devices)

1. Press and hold the button on the device you wish to synchronise for at least 5 seconds and then release.

2. Slowly press the button on the previously-synchronised remote control 3 times.

3. Slowly press the button on the device to be synchronised once.

Direct synchronisation procedure on the receiver

1. Press button P1 on the receiver and hold for at least 3 seconds.

2. Release the button when LED P1 lights up.

3. You have 10 seconds to press any button on the device to be synchronised for at least 2 seconds. LED P1 will flash 3 times if synchronisation has been performed successfully.

4. If you wish to synchronise additional remote controls, repeat step 2 within 10 seconds or the receiver will automatically exit synchronisation mode.