FIND YOUR REMOTE
Find your remote and compatable JMA Remote to copy
Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
FOR: APRIMATIC® TM 4
- F 433,92
- C ROLLING CODE
- B 4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING APRIMATIC ROLLING CODE REMOTE CONTROLS
Direct synchronisation procedure on the receiver
1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".
2. Press the button or turn on the switch.
The receiver will emit a long beep and the LED will light up. From this point, follow the previous procedure from step 2 above.
Synchronising the APRIMATIC TR remote control
1. Stand near the receiver and press all the emission keys of the device already synchronised in the facility.
The receiver will emit a continuous beep.
2. Press the synch button of the duplicated device.
3. Then press any key of the duplicated device.
The LED and buzzer will pause briefly and then resume, confirming that the remote control is now synchronised.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
FOR: APRIMATIC® TR
- F 433,92
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING APRIMATIC ROLLING CODE REMOTE CONTROLS
Direct synchronisation procedure on the receiver
1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".
2. Press the button or turn on the switch.
The receiver will emit a long beep and the LED will light up. From this point, follow the previous procedure from step 2 above.
Synchronising the APRIMATIC TR remote control
1. Stand near the receiver and press all the emission keys of the device already synchronised in the facility.
The receiver will emit a continuous beep.
2. Press the synch button of the duplicated device.
3. Then press any key of the duplicated device.
The LED and buzzer will pause briefly and then resume, confirming that the remote control is now synchronised.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
FOR: APRIMATIC® TS
- F 306
- C FIX CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
FOR: APRIMATIC® TX-E
- F 433,92
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING APRIMATIC TXM ROLLING CODE REMOTE CONTROLS
Remote synchronisation procedure for the APRIMATIC TXM remote control
1. Stand near the receiver and press all the emission keys of the device already synchronised in the facility.
The receiver will emit a beep and the LED will flash.
2. Press the synch button of the duplicated device.
The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.
3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the original or duplicated remote control.
The LED and buzzer will turn off.
Direct synchronisation procedure for the APRIMATIC TXM remote control
1. Open the receiver and press the small button located near the LED for 2 seconds.
The receiver LED will flash
2. Press the synch button of the duplicated device.
The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.
3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the master remote control.
The LED and buzzer will turn off.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
FOR: APRIMATIC® TX2P
- F 433,92
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING APRIMATIC TXM ROLLING CODE REMOTE CONTROLS
Remote synchronisation procedure for the APRIMATIC TXM remote control
1. Stand near the receiver and press all the emission keys of the device already synchronised in the facility.
The receiver will emit a beep and the LED will flash.
2. Press the synch button of the duplicated device.
The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.
3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the original or duplicated remote control.
The LED and buzzer will turn off.
Direct synchronisation procedure for the APRIMATIC TXM remote control
1. Open the receiver and press the small button located near the LED for 2 seconds.
The receiver LED will flash
2. Press the synch button of the duplicated device.
The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.
3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the master remote control.
The LED and buzzer will turn off.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
FOR: APRIMATIC® TX4S
- F 433,92
- C ROLLING CODE
- B 4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING APRIMATIC TXM ROLLING CODE REMOTE CONTROLS
Remote synchronisation procedure for the APRIMATIC TXM remote control
1. Stand near the receiver and press all the emission keys of the device already synchronised in the facility.
The receiver will emit a beep and the LED will flash.
2. Press the synch button of the duplicated device.
The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.
3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the original or duplicated remote control.
The LED and buzzer will turn off.
Direct synchronisation procedure for the APRIMATIC TXM remote control
1. Open the receiver and press the small button located near the LED for 2 seconds.
The receiver LED will flash
2. Press the synch button of the duplicated device.
The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.
3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the master remote control.
The LED and buzzer will turn off.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
FOR: APRIMATIC® TXM
- F 433,92
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING APRIMATIC TXM ROLLING CODE REMOTE CONTROLS
Remote synchronisation procedure for the APRIMATIC TXM remote control
1. Stand near the receiver and press all the emission keys of the device already synchronised in the facility.
The receiver will emit a beep and the LED will flash.
2. Press the synch button of the duplicated device.
The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.
3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the original or duplicated remote control.
The LED and buzzer will turn off.
Direct synchronisation procedure for the APRIMATIC TXM remote control
1. Open the receiver and press the small button located near the LED for 2 seconds.
The receiver LED will flash
2. Press the synch button of the duplicated device.
The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.
3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the master remote control.
The LED and buzzer will turn off.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.