FIND YOUR REMOTE
Find your remote and compatable JMA Remote to copy
Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
FOR: GENIUS® A25
- F 433,92
- C ROLLING CODE
- B 2,4
- AP NO
SYNCHRONISING GENIUS ROLLING CODE REMOTE CONTROLS
GENIUS remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.
Remote synchronising procedure
1. Press and hold buttons P1 and P2 on the remote control already synchronised in the facility for at least 5 seconds.
2. Within 10 seconds, press the same button on the remote control already synchronised in the facility as the one you wish to synchronise.
3. The receiver will enter synchronisation mode and the LED for the active channel will light up steady.
4. Press the button you wish to synchronise on the new remote control.
5. Repeat Step 4 if you wish to add more remote controls.
6. Wait for 10 seconds for the receiver to exit synchronisation mode.
7. Repeat the process for the other channel.
Direct synchronisation procedure on the receiver
1. Press the button on the receiver for the channel you wish to synchronise - SW1 to synchronise CH1 and SW2 to synchronise CH2. Either LED 1 or LED 2 will light up steady indicating that the receiver is in synchronisation mode.
2. Within 10 seconds press and hold the button you wish to synchronise on the remote control for at least 1 second.
3. If synchronisation is successful, the LED will flash a couple of times.
4. Repeat the process from Step 2 to synchronise additional remote controls.
5. The receiver will automatically exit synchronisation mode 10 seconds after the last synchronisation.
FOR: GENIUS® A25NEW
- F 433,92
- C ROLLING CODE
- B 2,4
- AP NO
SYNCHRONISING GENIUS ROLLING CODE REMOTE CONTROLS
GENIUS remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.
Remote synchronising procedure
1. Press and hold buttons P1 and P2 on the remote control already synchronised in the facility for at least 5 seconds.
2. Within 10 seconds, press the same button on the remote control already synchronised in the facility as the one you wish to synchronise.
3. The receiver will enter synchronisation mode and the LED for the active channel will light up steady.
4. Press the button you wish to synchronise on the new remote control.
5. Repeat Step 4 if you wish to add more remote controls.
6. Wait for 10 seconds for the receiver to exit synchronisation mode.
7. Repeat the process for the other channel.
Direct synchronisation procedure on the receiver
1. Press the button on the receiver for the channel you wish to synchronise - SW1 to synchronise CH1 and SW2 to synchronise CH2. Either LED 1 or LED 2 will light up steady indicating that the receiver is in synchronisation mode.
2. Within 10 seconds press and hold the button you wish to synchronise on the remote control for at least 1 second.
3. If synchronisation is successful, the LED will flash a couple of times.
4. Repeat the process from Step 2 to synchronise additional remote controls.
5. The receiver will automatically exit synchronisation mode 10 seconds after the last synchronisation.
FOR: GENIUS® AMIGO
- F 868,3
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING FAAC ROLLING CODE REMOTE CONTROLS
FAAC remote controls can be synchronised using a master remote control with its own code. In this case it is not necessary to work directly or remotely with the receiver.
Follow these steps to synchronise a slave remote control from a master device. This procedure is valid for the TML and 868 SLH series.
TML series
Warning: if you press the slave remote control first and then the master device you will delete the master codes.
1. Press the button of the already synchronised remote control and hold down.
2. Still holding down the master device button, press the same button on the slave with the two devices close to each other.
The LED on the slave will flash.
3. Repeat the operation for the remaining buttons.
SERIE 868SLH
Warning: if you press the slave remote control first and then the master device you will delete the master codes.
1. Press the two buttons on the master device until the LED starts flashing and release after one second (on devices with four buttons, press the top right and lower left buttons).
2. Before the master device LED stops flashing, press the top right button on the master device again with the remote controls close to each other. The master LED will change to steady.
3. Still holding down the master device button, press the same button on the slave.
The slave device LED will flash once to confirm that the code has been stored.
4. Release both buttons.
FOR: GENIUS® AMIGOLD
- F 868,3
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING FAAC ROLLING CODE REMOTE CONTROLS
FAAC remote controls can be synchronised using a master remote control with its own code. In this case it is not necessary to work directly or remotely with the receiver.
Follow these steps to synchronise a slave remote control from a master device. This procedure is valid for the TML and 868 SLH series.
TML series
Warning: if you press the slave remote control first and then the master device you will delete the master codes.
1. Press the button of the already synchronised remote control and hold down.
2. Still holding down the master device button, press the same button on the slave with the two devices close to each other.
The LED on the slave will flash.
3. Repeat the operation for the remaining buttons.
SERIE 868SLH
Warning: if you press the slave remote control first and then the master device you will delete the master codes.
1. Press the two buttons on the master device until the LED starts flashing and release after one second (on devices with four buttons, press the top right and lower left buttons).
2. Before the master device LED stops flashing, press the top right button on the master device again with the remote controls close to each other. The master LED will change to steady.
3. Still holding down the master device button, press the same button on the slave.
The slave device LED will flash once to confirm that the code has been stored.
4. Release both buttons.
FOR: GENIUS® BRAVO
- F 433,92
- C ROLLING CODE
- B 4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING GENIUS ROLLING CODE REMOTE CONTROLS
GENIUS remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.
Remote synchronising procedure
1. Press and hold buttons P1 and P2 on the remote control already synchronised in the facility for at least 5 seconds.
2. Within 10 seconds, press the same button on the remote control already synchronised in the facility as the one you wish to synchronise.
3. The receiver will enter synchronisation mode and the LED for the active channel will light up steady.
4. Press the button you wish to synchronise on the new remote control.
5. Repeat Step 4 if you wish to add more remote controls.
6. Wait for 10 seconds for the receiver to exit synchronisation mode.
7. Repeat the process for the other channel.
Direct synchronisation procedure on the receiver1. Press the button on the receiver for the channel you wish to synchronise - SW1 to synchronise CH1 and SW2 to synchronise CH2. Either LED 1 or LED 2 will light up steady indicating that the receiver is in synchronisation mode.
2. Within 10 seconds press and hold the button you wish to synchronise on the remote control for at least 1 second.
3. If synchronisation is successful, the LED will flash a couple of times.
4. Repeat the process from Step 2 to synchronise additional remote controls.
5. The receiver will automatically exit synchronisation mode 10 seconds after the last synchronisation.
FOR: GENIUS® ECHO TX RC
- F 433,92
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-48
SYNCHRONISING FAAC ROLLING CODE REMOTE CONTROLS
FAAC remote controls can be synchronised using a master remote control with its own code. In this case it is not necessary to work directly or remotely with the receiver.
Follow these steps to synchronise a slave remote control from a master device. This procedure is valid for the TML and 868 SLH series.
TML series
Warning: if you press the slave remote control first and then the master device you will delete the master codes.
1. Press the button of the already synchronised remote control and hold down.
2. Still holding down the master device button, press the same button on the slave with the two devices close to each other.
The LED on the slave will flash.
3. Repeat the operation for the remaining buttons.
SERIE 868SLH
Warning: if you press the slave remote control first and then the master device you will delete the master codes.
1. Press the two buttons on the master device until the LED starts flashing and release after one second (on devices with four buttons, press the top right and lower left buttons).
2. Before the master device LED stops flashing, press the top right button on the master device again with the remote controls close to each other. The master LED will change to steady.
3. Still holding down the master device button, press the same button on the slave.
The slave device LED will flash once to confirm that the code has been stored.
4. Release both buttons.
FOR: GENIUS® JA332 AMIGO
- F 868,3
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-48
SYNCHRONISING FAAC ROLLING CODE REMOTE CONTROLS
FAAC remote controls can be synchronised using a master remote control with its own code. In this case it is not necessary to work directly or remotely with the receiver.
Follow these steps to synchronise a slave remote control from a master device. This procedure is valid for the TML and 868 SLH series.
TML series
Warning: if you press the slave remote control first and then the master device you will delete the master codes.
1. Press the button of the already synchronised remote control and hold down.
2. Still holding down the master device button, press the same button on the slave with the two devices close to each other.
The LED on the slave will flash.
3. Repeat the operation for the remaining buttons.
SERIE 868SLH
Warning: if you press the slave remote control first and then the master device you will delete the master codes.
1. Press the two buttons on the master device until the LED starts flashing and release after one second (on devices with four buttons, press the top right and lower left buttons).
2. Before the master device LED stops flashing, press the top right button on the master device again with the remote controls close to each other. The master LED will change to steady.
3. Still holding down the master device button, press the same button on the slave.
The slave device LED will flash once to confirm that the code has been stored.
4. Release both buttons.
FOR: GENIUS® JA40
- F 433,92
- C FIX CODE
- B 1,2,3
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
FOR: GENIUS® KILO
- F 868,3
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-48
SYNCHRONISING FAAC ROLLING CODE REMOTE CONTROLS
FAAC remote controls can be synchronised using a master remote control with its own code. In this case it is not necessary to work directly or remotely with the receiver.
Follow these steps to synchronise a slave remote control from a master device. This procedure is valid for the TML and 868 SLH series.
TML series
Warning: if you press the slave remote control first and then the master device you will delete the master codes.
1. Press the button of the already synchronised remote control and hold down.
2. Still holding down the master device button, press the same button on the slave with the two devices close to each other.
The LED on the slave will flash.
3. Repeat the operation for the remaining buttons.
SERIE 868SLH
Warning: if you press the slave remote control first and then the master device you will delete the master codes.
1. Press the two buttons on the master device until the LED starts flashing and release after one second (on devices with four buttons, press the top right and lower left buttons).
2. Before the master device LED stops flashing, press the top right button on the master device again with the remote controls close to each other. The master LED will change to steady.
3. Still holding down the master device button, press the same button on the slave.
The slave device LED will flash once to confirm that the code has been stored.
4. Release both buttons.