Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
TELCOMA® FOX 30 Remote
EXTEL® S466 Remote
CRAWFORD® EA433K Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING CRAWFORD/NORMSTHAL ROLLING CODE REMOTE CONTROLS
CRAWFORD/NORMSTHAL remote controls can only be synchronised directly on the receiver by taking the following steps.
Synchronisation procedure using the receiver
1. Press the SET button:
Once for impulse response (the receiver is active while the button is being held)
Twice for flip-flop response (the receiver is active until the next time it is pressed)
Three times for ON
Four times for OFF
2. Press the button of the device to be synchronised
3. The LED will flash, indicating that the code has been stored.
TELCOMA® RCKTM Remote
STAGNOLI® KALLISTO Remote
NOVOFERM® S41 Remote
OPEN OUT® DOMINO Remote
- F 433,92
- C ROLLING CODE
- B 4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING GIBIDI ROLLING CODE REMOTE CONTROLS
Direct synchronisation procedure on the receiver
1. Open the receiver and locate the programming button on the circuit board.
2. Press it briefly.
The receiver LED will flash.
3. Within 10 seconds, press the button of the remote control you wish to synchronise.
The receiver will automatically exit synchronisation mode after a short time.
SEAV® BE SMART S2 Remote
- F 433,92
- C FIX CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
PUJOL® Universal Remote
- F 433,92
- C ROLLING CODE
- B 4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING THE PUJOL VARIO ROLLING CODE REMOTE CONTROLS
PUJOL VARIO rolling code remote controls are synchronised using the same procedure as for JMC devices.
There are 3 synchronisation procedures for these devices.
PIN-MODE remote synchronising procedure
The following procedure must be applied if the receiver bears the words PIN-MODE:
1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the remote control you wish to synchronise.
The receiver will emit a long beep, indicating that the device has been successfully synchronised.
Remote synchronisation procedure using the original remote control
1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the synchronised remote control.
The receiver will emit a beep, indicating that it has switched to synchronisation mode.
2. Within 10 seconds of the beep, press the button on the device to be synchronised.
The receiver will emit another short beep to indicate that the remote control has been synchronised.
If the receiver fails to synchronise the device (does not emit the beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.
3. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.
Direct synchronisation procedure on the receiver
1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".
2. Press the button or turn on the switch.
The receiver will emit a beep and the LED will light up. From this point, follow the previous procedure from step 2 above.
STAGNOLI® ZEUS Remote
- F 433,92
- C FIX CODE
- B 3
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
EXTEL® ATEM2 Remote
EXTEL® ATEM4 Remote
The selected remotes can not be copied with a single JMA remote