Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
GIBIDI® L110 Remote
- F 305
- C FIX CODE
- B 1
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
DICKERT® AHS27 Remote
SOMMER® 4010 Remote
GIBIDI® GIOTTO Remote
- F 433,92
- C ROLLING CODE
- B 2
- AP YES
- M-NOVA PRO / BT Slim / M-BT Biometric / M-BT Advance / SR-4V / SR-48
DICKERT® FHS20-K Remote
DICKERT® FHS10B Remote
DICKERT® MAHS27 Remote
DICKERT® FHS10-L Remote
SOMMER® 4025 433 Remote
- F 433,92
- C ROLLING CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING SOMMER ROLLING CODE REMOTE CONTROLS
SOMMER remote control can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver
1. Press button B on the receiver
a. Once for channel 1. LED (C1) will light up.
b. Twice for channel 2. LED (C2) will light up.
The receiver will exit synchronisation mode if no code is transmitted during a period of 10 seconds.
To exit synchronisation mode, press key B several times until all LEDs have turned off.
2. Press the desired button (D) on the remote control. The transmitter will send the radio code to the receiver.
The LED for the selected channel will flash and switch off.
Repeat Steps 1 and 2 to synchronise additional transmitters with this receiver.
GIBIDI® DOMINO Remote
- F 433,92
- C ROLLING CODE
- B 4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING GIBIDI ROLLING CODE REMOTE CONTROLS
Direct synchronisation procedure on the receiver
1. Open the receiver and locate the programming button on the circuit board.
2. Press it briefly.
The receiver LED will flash.
3. Within 10 seconds, press the button of the remote control you wish to synchronise.
The receiver will automatically exit synchronisation mode after a short time.
GIBIDI® GIBIDI 26,995 Remote
GIBIDI® AU1600 WOOD Remote
- F 433,92
- C ROLLING CODE
- B 2
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING GIBIDI ROLLING CODE REMOTE CONTROLS
Direct synchronisation procedure on the receiver
1. Open the receiver and locate the programming button on the circuit board.
2. Press it briefly.
The receiver LED will flash.
3. Within 10 seconds, press the button of the remote control you wish to synchronise.
The receiver will automatically exit synchronisation mode after a short time.
The selected remotes can not be copied with a single JMA remote
