Print

SYNCHRONISING LIFT MASTER ROLLING CODE REMOTE CONTROLS

The Lift Master remote control can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver

1. Press the button on the remote control and hold.

2. Press and release the Learn button for channel A on the receiver.

3. The control LED will flash once.

4. Release the remote control button.

If you release the remote control button before the control LED flashes the receiver will not accept the code.

Repeat this procedure for any other devices you wish to add.

If you are using a second door, select another button on the remote control and repeat the steps for channel B.

Print

SYNCHRONISING AERF ROLLING CODE REMOTE CONTROLS

The JCM rolling code remote control synchronisation procedure is identical for all models, including customised models, except the 868 MHz.

There are two synchronisation procedures for these devices.

Remote synchronisation procedure using the original remote control

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the remote control already synchronised in the facility. If there is no rear button, press all the buttons on the original device at once.

The receiver will emit a beep, indicating that it has switched to synchronisation mode.

2. Within 10 seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

3. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Print

SYNCHRONISING CRAWFORD/NORMSTHAL ROLLING CODE REMOTE CONTROLS

CRAWFORD/NORMSTHAL remote controls can only be synchronised directly on the receiver by taking the following steps.

Synchronisation procedure using the receiver

1. Press the SET button:

Once for impulse response (the receiver is active while the button is being held)

Twice for flip-flop response (the receiver is active until the next time it is pressed)

Three times for ON

Four times for OFF

2. Press the button of the device to be synchronised

3. The LED will flash, indicating that the code has been stored.

Print

SYNCHRONISING ERREKA ROLLING CODE REMOTE CONTROLS

Erreka remote control receivers enable remote synchronisation without handling the receiver or using the button on its circuit board.

ROLLER REMOTE CONTROLS

Remote synchronising procedure

1. Stand near the receiver, open the battery cover on the remote control already synchronised in the facility and press the button next to the battery or the synch button.

Release as soon as the LED on the receiver lights up

2. Press the button of the device to be synchronised.

The receiver will emit a beep to indicate that the remote control has been synchronised.

If the receiver fails to emit a beep it means that the procedure has failed, probably for the following reasons:

- The memory is full. The installer may have filled it on purpose. In this case, no devices can be synchronised without contacting the installer.

3. Wait for 30 seconds until the LED turns off, indicating that the receiver has exited synchronisation mode.

Direct synchronisation procedure on the receiver

1. Open the receiver and set the switch to the ON position.

The LED on the receiver will light up. From this point, follow the previous procedure from step 2 above.

SOL REMOTE CONTROLS

Both synchronisation procedures are identical to those for the ROLLER remote controls. The only difference is that a jumper must connect the first and fifth pins in the original remote control activate synchronisation mode in the receiver, and remove the jumper once this has been done.

This will not be necessary if synchronisation mode is activated from a synchronised remote control since the device is provided with a button for this purpose at the rear.

Print

SYNCHRONISING GO ROLLING CODE REMOTE CONTROLS

The GO remote control is synchronised directly with the receiver the first time the button is pressed. However, this option is disabled on some models, which must be synchronised manually.

GO remote control manual synchronisation procedure

1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".

2. Press the button or turn on the switch.

3. Within ten (10) seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

4. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING GIBIDI ROLLING CODE REMOTE CONTROLS

Direct synchronisation procedure on the receiver

1. Open the receiver and locate the programming button on the circuit board.

2. Press it briefly.

The receiver LED will flash.

3. Within 10 seconds, press the button of the remote control you wish to synchronise.

The receiver will automatically exit synchronisation mode after a short time.