Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
CASIT® TXS Remote
- F 433,92
- C FIX CODE
- B 1,2,3,4,6
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
CARDIN® S438 TX Remote
- F 433,92
- C FIX CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
KEY® TXG-44R Remote
- F 433,92
- C ROLLING CODE
- B 4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING KEY ROLLING CODE REMOTE CONTROLS
KEY remote controls can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver (type A receiver)
1. Press button S on the receiver.
2. The LED (Ir1) will light up.
3. Release button S and press button P.
4. The LED (Ir1) will flash once.
5. Release the button.
6. Press the button of the remote control to be synchronised until the LED (Ir1) begins to flash, then release.
7. Wait for 10 seconds for the receiver to exit synchronisation mode.
Direct synchronisation procedure on the receiver (type B receiver)
1. Press KEY the same number of times as the channel you wish to synchronise (one time for channel 1, two times for channel 2, etc.).
2. The LED will flash the number of times equal to the number of the selected channel.
3. Within the next 7 seconds, press the button on the remote control to be synchronised for 2 seconds.4. The LED will flash once if synchronisation has been successful.
5. Repeat step 3 if you wish to add more remote controls.
BENINCA® CUPIDO NEGRO Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING BENINCA ROLLING CODE REMOTE CONTROLS
Remote synchronisation procedure for the BENINCA remote control
1. Stand near the receiver and press the already synchronised hidden transmitter key.
2. Within 5 seconds press the key on the already synchronised remote control that corresponds to the channel to be associated with the new device.
3. Within 5 seconds, press the key of the new device to be associated with the channel selected in step 2.
The receiver will memorise the new transmitter and exit synchronisation mode immediately.
Direct synchronisation procedure for the BENINCA remote control
1. Open the receiver and briefly press the P button.
The red LED on the receiver will light up for 3 seconds, turn off for 1 second and light up for a further 5 seconds.
2. While the red LED is lit up, press the transmitter button that you want to synchronise with channel 1.
Other transmitters can also be entered. You only have to press a key before 5 seconds elapse since the previous device was synchronised.
3. Once finished, wait 5 seconds until the receiver exits synchronisation mode.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
FAAC® R40 330 ANTIGUO Remote
- F 330
- C FIX CODE
- B 1,2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
WAYNE DALTON® TX02433 Remote
- F 433,92
- C ROLLING CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING SOMMER ROLLING CODE REMOTE CONTROLS
SOMMER remote control can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver
1. Press button B on the receiver
a. Once for channel 1. LED (C1) will light up.
b. Twice for channel 2. LED (C2) will light up.
The receiver will exit synchronisation mode if no code is transmitted during a period of 10 seconds.
To exit synchronisation mode, press key B several times until all LEDs have turned off.
2. Press the desired button (D) on the remote control. The transmitter will send the radio code to the receiver.
The LED for the selected channel will flash and switch off.
Repeat Steps 1 and 2 to synchronise additional transmitters with this receiver.
GIBIDI® AU1680 WOOD Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING GIBIDI ROLLING CODE REMOTE CONTROLS
Direct synchronisation procedure on the receiver
1. Open the receiver and locate the programming button on the circuit board.
2. Press it briefly.
The receiver LED will flash.
3. Within 10 seconds, press the button of the remote control you wish to synchronise.
The receiver will automatically exit synchronisation mode after a short time.
