Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
SEAV® BE SMART RS2 Remote
MHOUSE® TX4 Remote
- F 433,92
- C ROLLING CODE
- B 4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING MHOUSE ROLLING CODE REMOTE CONTROLS
MHOUSE remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.
Remote synchronisation procedure (identical to procedure for NICE, Smilo and Flo-R devices)
1. Press and hold the button on the device you wish to synchronise for at least 5 seconds and then release.
2. Slowly press the button on the previously-synchronised remote control 3 times.
3. Slowly press the button on the device to be synchronised once.
Direct synchronisation procedure on the receiver
1. Press button P1 on the receiver and hold for at least 3 seconds.
2. Release the button when LED P1 lights up.
3. You have 10 seconds to press any button on the device to be synchronised for at least 2 seconds. LED P1 will flash 3 times if synchronisation has been performed successfully.
4. If you wish to synchronise additional remote controls, repeat step 2 within 10 seconds or the receiver will automatically exit synchronisation mode.
ROLLTORE® R40-330 NEW Remote
- F 330
- C FIX CODE
- B 1,2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
MHOUSE® MOOVO Remote
- F 433,92
- C ROLLING CODE
- B 4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING MHOUSE ROLLING CODE REMOTE CONTROLS
MHOUSE remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.
Remote synchronisation procedure (identical to procedure for NICE, Smilo and Flo-R devices)
1. Press and hold the button on the device you wish to synchronise for at least 5 seconds and then release.
2. Slowly press the button on the previously-synchronised remote control 3 times.
3. Slowly press the button on the device to be synchronised once.
Direct synchronisation procedure on the receiver
1. Press button P1 on the receiver and hold for at least 3 seconds.
2. Release the button when LED P1 lights up.
3. You have 10 seconds to press any button on the device to be synchronised for at least 2 seconds. LED P1 will flash 3 times if synchronisation has been performed successfully.
4. If you wish to synchronise additional remote controls, repeat step 2 within 10 seconds or the receiver will automatically exit synchronisation mode.
BFT® 306 Remote
- F 306
- C FIX CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
BFT® BRC B VINEYARD Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING BFT ROLLING CODE REMOTE CONTROLS
The receivers of these models enable remote or direct synchronisation.
Remote synchronisation procedure for the BFT MITTO remote control
1. Stand near the receiver and press the hidden button at the rear of the BFT original remote control for 2 seconds.
2. Press the left button on the front of the original remote control for 2 seconds.
3. Press the synch button on the rear of the device to be synchronised.
4. Finally, press the first button on the device to be synchronised.
Remote synchronisation procedure for the BFT TRC or MITTO remote control
1. Open the receiver and locate the SW-1 and SW-2 buttons. Press the first (SW-1).
A flashing LED should light up in the receiver.
2. Open the battery cover of the already synchronised remote control or the one you have copied and press the button inside.
The receiver light should change to steady.
3. Press the button of the device to be synchronised.
The light on the receiver will return to flashing and turn off after 30 seconds, indicating that the synchronisation process has finished.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
The selected remotes can not be copied with a single JMA remote