Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
AVIDSEN® 104250 RED Remote
- F 433,92
- C ROLLING CODE
- B 4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
SYNCHRONISING V2 ROLLING CODE REMOTE CONTROLS
V2 remote controls can be synchronised either remotely or directly on the receiver.
Remote synchronising procedure
1. Press buttons 1 and 2 on the remote control to be synchronised simultaneously for approximately 10 seconds.
2. Release.
3. Within 5 seconds, press any other button on the device to be synchronised.
4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.
The code has been stored.
Since this option is not enabled on all models we recommend the following procedure.
Direct synchronisation procedure on the receiver
1. Open the receiver and locate the small SW1 button.
2. Press until the receiver LED lights up.
3. Within 5 seconds, press the button on the remote control to be synchronised and hold until the receiver LED blinks.
4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.
The code has been stored.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
KEY® TXG-44 Remote
- F 433,92
- C FIX CODE
- B 4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SOMMER® 4025 Remote
- F 868,3
- C ROLLING CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING SOMMER ROLLING CODE REMOTE CONTROLS
SOMMER remote control can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver
1. Press button B on the receiver
a. Once for channel 1. LED (C1) will light up.
b. Twice for channel 2. LED (C2) will light up.
The receiver will exit synchronisation mode if no code is transmitted during a period of 10 seconds.
To exit synchronisation mode, press key B several times until all LEDs have turned off.
2. Press the desired button (D) on the remote control. The transmitter will send the radio code to the receiver.
The LED for the selected channel will flash and switch off.
Repeat Steps 1 and 2 to synchronise additional transmitters with this receiver.
DTM SYSTEM® NE0 Remote
- F 433,92MHz
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-NOVA PRO / M-BT Advance
HOW TO SYNCHRONISE DTM NEO SPACE ROLLING CODE REMOTE CONTROLS
DTM NEO remote control synchronisation can be performed either directly on the receiver itself or remotely using a remote control that is already synchronised with the receiver.
Remotely synchronising the remote control on the receiver
1. While holding the receiver’s button, press a button in the remote which you want to register. The light will blink.
While registering the remote in the receiver’s memory, the button controlling the output channel must be used. Only one button of the remote can be registered. Registering another button of the same remote will result in removing the previous one.
Synchronising the remote control directly on the receiver
1. press and hold button in previously registered remote for 15 seconds,
2. press and hold button in a remote which you want to register for 15 seconds, within 3 seconds after releasing the previous button,
3. the new remote is now registered with the same active button as in the previously registered remote.
CHAMBERLAIN 2.0® 893LM Remote
SYNCHRONISING LIFT MASTER ROLLING CODE REMOTE CONTROLS
The Lift Master remote control can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver
1. Press the button on the remote control and hold.
2. Press and release the Learn button for channel A on the receiver.
3. The control LED will flash once.
4. Release the remote control button.
If you release the remote control button before the control LED flashes the receiver will not accept the code.
Repeat this procedure for any other devices you wish to add.
If you are using a second door, select another button on the remote control and repeat the steps for channel B.
