Print

SYNCHRONISING BENINCA ROLLING CODE REMOTE CONTROLS

Remote synchronisation procedure for the BENINCA remote control

1. Stand near the receiver and press the already synchronised hidden transmitter key.

2. Within 5 seconds press the key on the already synchronised remote control that corresponds to the channel to be associated with the new device.

3. Within 5 seconds, press the key of the new device to be associated with the channel selected in step 2.

The receiver will memorise the new transmitter and exit synchronisation mode immediately.

Direct synchronisation procedure for the BENINCA remote control

1. Open the receiver and briefly press the P button.

The red LED on the receiver will light up for 3 seconds, turn off for 1 second and light up for a further 5 seconds.

2. While the red LED is lit up, press the transmitter button that you want to synchronise with channel 1.

Other transmitters can also be entered. You only have to press a key before 5 seconds elapse since the previous device was synchronised.

3. Once finished, wait 5 seconds until the receiver exits synchronisation mode.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING SOMMER ROLLING CODE REMOTE CONTROLS

SOMMER remote control can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver

1. Press button B on the receiver

a. Once for channel 1. LED (C1) will light up.

b. Twice for channel 2. LED (C2) will light up.

The receiver will exit synchronisation mode if no code is transmitted during a period of 10 seconds.

To exit synchronisation mode, press key B several times until all LEDs have turned off.

2. Press the desired button (D) on the remote control. The transmitter will send the radio code to the receiver.

The LED for the selected channel will flash and switch off.

Repeat Steps 1 and 2 to synchronise additional transmitters with this receiver.

Print

SYNCHRONISING BFT ROLLING CODE REMOTE CONTROLS

The receivers of these models enable remote or direct synchronisation.

Remote synchronisation procedure for the BFT MITTO remote control

1. Stand near the receiver and press the hidden button at the rear of the BFT original remote control for 2 seconds.

2. Press the left button on the front of the original remote control for 2 seconds.

3. Press the synch button on the rear of the device to be synchronised.

4. Finally, press the first button on the device to be synchronised.

Remote synchronisation procedure for the BFT TRC or MITTO remote control

1. Open the receiver and locate the SW-1 and SW-2 buttons. Press the first (SW-1).

A flashing LED should light up in the receiver.

2. Open the battery cover of the already synchronised remote control or the one you have copied and press the button inside.

The receiver light should change to steady.

3. Press the button of the device to be synchronised.

The light on the receiver will return to flashing and turn off after 30 seconds, indicating that the synchronisation process has finished.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING SOMFY ROLLING CODE REMOTE CONTROLS

SOMFY remote control can only be synchronised directly on the external receiver and remotely on the integrated shutter receiver. A distinction must be made between SOMFY and TELIS remote controls.

Synchronisation procedure on the receiver

External receiver

1. Press and hold the \"Prog\" button on the receiver for 2 seconds. The red LED on the receiver will remain lit.

Internal receiver (Telis)

1. Press and hold the up and down buttons on the Telis remote control for 2 seconds. The red LED on the receiver will remain lit.

Keytis remote control

2. Press the button of the device to be synchronised. The LED on the receiver will flash.

3. Wait until the LED turns off.

Telis 1RTS remote control

2. Press the rear button on the remote control for half a second. The LED on the receiver will flash.

3. Wait until the LED turns off.

Telis 4 RTS remote control

2. Press the channel selection button until the LED for the desired channel lights up.

3. Press the rear button on the remote control for half a second. The LED on the receiver will flash.

4. Wait until the LED turns off.

Print

SYNCHRONISING PRASTEL ROLLING CODE REMOTE CONTROL

PRASTEL remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.

Remote synchronisation procedure

1. Stand near the receiver (1-2 metres) with the synchronised device.

2. Press and release buttons 1 and 2 simultaneously.

3. The LED on the remote control will light up after two seconds and turn off.

4. When the LED on the remote control lights up again, simultaneously press buttons 1 and 2 and hold until the LED begins to flash.

5. When the LED stops flashing the remote control will activate the synchronisation mode of the receiver.

6. The receiver will remain in synchronisation mode for around 10 seconds.

7. Press one of the buttons on the remote control to be synchronised.

8. The receiver will save the code.

Direct synchronisation procedure on the receiver

1. Connect the receiver to the power supply.

2. Press the ENTER RADIO button. All the red LEDS will light up for 2 seconds, after which only the first LED will remain lit.

3. Press the \"SET\" button repeatedly to select the relay you wish to associate with the transmission.

4. Press the desired button to transmit the code. Each button (channel) transmits a different code.

a. The LED flashes slowly during synchronisation and remains steady once the operation has been successfully concluded.

b. If a LED begins to flash quickly, it means that this channel has already been synchronised and associated with the LED concerned. Repeat the operation to change allocation of the relay prior to the one currently selected.

c. If all the LEDS flash at once it means that the memory is full. The code has not been stored.

5. Repeat the operation for all buttons (channels) you wish to synchronise, always selecting the relay to which they are to be associated.

6. Repeat the operation for all the remote controls you wish to synchronise.

7. Press ENTER RADIO again to exit synchronisation mode. The LEDS will turn off. The device will exit synchronisation mode automatically 10 seconds after the last operation.

8. The codes are stored and will not be deleted even in the event of a power cut.

Print

DAR DE ALTA MANDOS EVOLUTIVOS DEA

SYNCHRONISING DEA ROLLING CODE REMOTE CONTROLS

DEA receivers can work in fixed or rolling code mode. These modes can be selected by placing a jumper in certain positions. The jumper is located in the centre of the circuit board and the positions are marked A (fixed position) and B (rolling code mode).

In rolling code mode, DEA remote controls can be synchronised either remotely or directly on the receiver.

Remote synchronising procedure

1. Stand near the receiver and simultaneously press the two buttons of the device already synchronised in the facility.

The LED on the receiver will light up steady, indicating that it has switched to synchronisation mode.

2. Within 5 seconds, press the button of the device to be synchronised.

The receiver LED will flash and then turn off, indicating that device has been successfully synchronised.

Direct synchronisation procedure on the receiver

1. Open the receiver and press and release the P1 pushbutton located to the right of the circuit board, below a LED.

The LED will light up, indicating that the receiver has entered synchronisation mode.

Be sure to release the P1 button as soon as the LED lights up. If the button is held down until the LED turns off, it will delete the contents of the receiver\'s memory.

2. Press the left button of the device to be synchronised.

The receiver LED will flash once, indicating that device has been successfully synchronised.

3. Synchronisation has been successfully performed. Repeat step 2 for each additional remote control you wish to synchronise. Otherwise, wait until the LED turns off after storing the code and the receiver exits synchronisation mode.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices. In this case only the installer will be able to synchronise any new remote controls.