Print

SYNCHRONISING LIFT MASTER ROLLING CODE REMOTE CONTROLS

The Lift Master remote control can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver

1. Press the button on the remote control and hold.

2. Press and release the Learn button for channel A on the receiver.

3. The control LED will flash once.

4. Release the remote control button.

If you release the remote control button before the control LED flashes the receiver will not accept the code.

Repeat this procedure for any other devices you wish to add.

If you are using a second door, select another button on the remote control and repeat the steps for channel B.

Print

SYNCHRONISING LIFT MASTER ROLLING CODE REMOTE CONTROLS

The Lift Master remote control can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver

1. Press the button on the remote control and hold.

2. Press and release the Learn button for channel A on the receiver.

3. The control LED will flash once.

4. Release the remote control button.

If you release the remote control button before the control LED flashes the receiver will not accept the code.

Repeat this procedure for any other devices you wish to add.

If you are using a second door, select another button on the remote control and repeat the steps for channel B.

Print

HOW TO SYNCHRONISE SMINN ROLLING CODE REMOTE CONTROLS

SMINN remote control synchronisation can be performed directly on the receiver itself or via radio by invitation.

Synchronising the remote control directly on the receiver

1. Press and hold button K1 (fig. 1 - component 3).

2. Press the button for the channel on the transmitter that you want to record and that will be assigned to Output 1 (relay K1) on the receiver board. On receiving the code and channel sent by the transmitter, the receiver records it in its memory and beeps TWICE consecutively to confirm.

ONLY FOR RECORDING THE FIRST CODE.

3. Press the button for the channel on the transmitter that you want to assign to Output 2 (relay K2) on the receiver board. On receiving the code and channel sent by the transmitter, the receiver records it in its memory and beeps THREE TIMES to confirm.

4. Release the synchronisation button on the receiver.

Synchronising the remote control via radio

Copying a transmitter that already works on the installation enables the copy to self-synchronise the first time it is used.

Print

SYNCHRONISING DITEC ROLLING CODE REMOTE CONTROLS

Remote synchronisation procedure for the DITEC remote control

1. Stand near the receiver and use a pointed object to press the button located below the central orifice of the Ditec remote control already synchronised in the facility for 5 seconds.

The LED on the master remote control will begin to flash after 5 seconds, indicating that it is ordering the receiver to enter synchronisation mode.

2. Press the synch button of the duplicated device.

The code of the new device is sent to the receiver and stored.

3. Wait for 10 seconds for the receiver to exit synchronisation mode.

Direct synchronisation procedure for the DITEC remote control

1. Open the receiver and press the small button marked PROG for 2 seconds.

The receiver LED will light up.

2. Press the synch button of the duplicated device.

The receiver LED will flash once and return to steady.

3. Wait for 10 seconds for the receiver to exit synchronisation mode.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING SKYMASTER ROLLING CODE REMOTE CONTROLS

SKYMASTER remote controls can only be synchronised directly on the receiver. The process is as follows.

Synchronisation procedure on the receiver

1. Press the CODE button once.

The red LED will begin the flash.

2. Press the button on the remote control to be synchronised twice.

The red LED will change to steady and then turn off.

3. Repeat the operation for every button (channel) and every device you wish to synchronise.

If the remote control being synchronised is the first one, you will have to delete the memory as follows:

1. Press and hold the CODE button for 8 seconds during which the LED will remain steady

2. The red LED will turn of and the memory will be deleted.

Print

SYNCHRONISING GO ROLLING CODE REMOTE CONTROLS

The GO remote control is synchronised directly with the receiver the first time the button is pressed. However, this option is disabled on some models, which must be synchronised manually.

GO remote control manual synchronisation procedure

1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".

2. Press the button or turn on the switch.

3. Within ten (10) seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

4. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

HOW TO SYNCHRONISE ELVOX ROLLING CODE REMOTE CONTROLS

ELVOX remote control synchronisation can only be performed directly on the receiver itself.

Synchronising the remote control directly on the receiver

Sliding and hinged doors

1. Hold the button on the receiver I2(P2).

2. While still holding the button on the receiver, press the button on the remote control to be synchronised.

3. Wait for the LED to flash, confirming the synchronisation.

4. Release both buttons.

ECRU receiver

1. Hold the button on the P1 receiver for two seconds. The DL1 LED will flash green.

2. Release the P1 button on the receiver.

3. Press button 1 on the remote control to be programmed.

4. The blue DL5 LED will flash.

5. On pressing the P1 button again for two seconds, the DL2 LED will flash green to synchronise channel 2.

6. Press button 2 on the remote control to be programmed.

7. The blue DL5 LED will flash.

8. To synchronise buttons 3 and 4, repeat steps 5 to 7. The LEDs DL3 and DL4 will light. Press buttons 3 and 4 in each case.

9. To leave synchronisation mode, press buttons P1 and P2 when the green LED flashes while waiting for a signal.

Print

SYNCHRONISING NOVOFERM ROLLING CODE REMOTE CONTROLS

The Novoferm remote control can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver

1. Open the receiver and press the button located inside until the LED begins to flash.

2. Then press the button on the remote control and hold for approximately 3 seconds until the LED begins to flash quickly.

Take the following steps if the facility has a ceiling-mounted motor.

Print

SYNCHRONISING GO ROLLING CODE REMOTE CONTROLS

The GO remote control is synchronised directly with the receiver the first time the button is pressed. However, this option is disabled on some models, which must be synchronised manually.

GO remote control manual synchronisation procedure

1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".

2. Press the button or turn on the switch.

3. Within ten (10) seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

4. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING JCM ROLLING CODE REMOTE CONTROLS

The JCM rolling code remote control synchronisation procedure is identical for all models except the 868 MHz.

There are 3 synchronisation procedures for these devices.

PIN-MODE remote synchronising procedure

The following procedure must be applied if the receiver bears the words PIN-MODE:

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the remote control to be synchronised.

The receiver will emit a long beep, indicating that the device has been successfully synchronised.

Remote synchronisation procedure using the original remote control

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the synchronised remote control.

The receiver will emit a beep, indicating that it has switched to synchronisation mode.

2. Within 10 seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

3. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Direct synchronisation procedure on the receiver

1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".

2. Press the button or turn on the switch.

The receiver will emit a long beep and the LED will light up. From this point, follow the previous procedure from step 2 above.

Print

HOW TO SYNCHRONISE SEAV ROLLING CODE REMOTE CONTROLS

Remote synchronisation procedure for SEAV remote controls

1. Stand near the receiver and press the first desired channel on the already synchronised (master) remote control for 15 seconds.

The receiver LED will begin to flash while it is waiting for transmission of a code.

2. Press the button for the same channel on the remote control to be synchronised (slave).

The receiver LED will light up steady, indicating that the channel has been synchronised.

Repeat the operation for the remaining channels.

Direct synchronisation procedure for SEAV remote controls

1. Open the receiver and press the button marked SEL.

The CODE CH1 LED will begin to flash while it is waiting for transmission of a code.

2. Press the button for the same channel on the remote control to be synchronised (slave).

The receiver LED will light up steady, indicating that the channel has been synchronised.

Repeat the same process for the second channel but pressing the SEL button twice (the CODE CH2 LED will flash) and pressing the second button on the slave device.

Observations

If the procedure fails, it may mean that the receiver memory is full, preventing synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING TELCOMA FM ROLLING CODE REMOTE CONTROLS

TELCOMA FM remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.

Remote synchronisation procedure

This procedure requires at least one four-channel remote control with the previous system already synchronised with the receiver.

1. Press the 4 buttons on the remote control already synchronised with the receiver simultaneously for 3 seconds.

2. Release, and within 2 seconds briefly press, on the same original device, the button that the receiver has already synchronised.

3. Within 2 seconds press the button of the remote control you wish to synchronise.

4. Repeat the process for the remaining buttons if necessary.

Direct synchronisation procedure on the receiver

1. On the receiver, press the P button associated with the channel to be synchronised with the remote control.

2. The LED will flash 5 times.

3. While the LED is flashing press the button on the remote control associated with the code to be synchronised.

4. If synchronisation is successful, the LED will emit a long flash.

5. Repeat the operation for all other remote controls you wish to synchronise.

Print

SYNCHRONISING SEAV ROLLING CODE REMOTE CONTROLS

Remote synchronisation procedure for the SEAV remote control

1. Stand near the receiver and press the first desired channel on the already synchronised remote control for 15 seconds.

The receiver LED will begin to flash while it is waiting for transmission of a code.

2. Press the button for the same channel on the remote control to be synchronised.

The receiver LED will light up steady, indicating that the channel has been synchronised.

Repeat the operation for the remaining buttons.

Direct synchronisation procedure for the SEAV remote control

1. Open the receiver and press the button marked SEL.

The CODE CH1 LED will begin to flash while it is waiting for transmission of a code.

2. Press the button for the same channel on the remote control to be synchronised.

The receiver LED will light up steady, indicating that the channel has been synchronised.

Repeat the same process for the second channel but pressing the SEL button twice (the CODE CH2 LED will flash) and pressing the second button on the duplicated device.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING FAAC ROLLING CODE REMOTE CONTROLS

FAAC remote controls can be synchronised using a master remote control with its own code. In this case it is not necessary to work directly or remotely with the receiver.

Follow these steps to synchronise a slave remote control from a master device. This procedure is valid for the TML and 868 SLH series.

TML series

Warning: if you press the slave remote control first and then the master device you will delete the master codes.

1. Press the button of the already synchronised remote control and hold down.

2. Still holding down the master device button, press the same button on the slave with the two devices close to each other.

The LED on the slave will flash.

3. Repeat the operation for the remaining buttons.

SERIE 868SLH

Warning: if you press the slave remote control first and then the master device you will delete the master codes.

1. Press the two buttons on the master device until the LED starts flashing and release after one second (on devices with four buttons, press the top right and lower left buttons).

2. Before the master device LED stops flashing, press the top right button on the master device again with the remote controls close to each other. The master LED will change to steady.

3. Still holding down the master device button, press the same button on the slave.

The slave device LED will flash once to confirm that the code has been stored.

4. Release both buttons.