Print

SYNCHRONISING AERF ROLLING CODE REMOTE CONTROLS

The JCM rolling code remote control synchronisation procedure is identical for all models, including customised models, except the 868 MHz.

There are two synchronisation procedures for these devices.

Remote synchronisation procedure using the original remote control

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the remote control already synchronised in the facility. If there is no rear button, press all the buttons on the original device at once.

The receiver will emit a beep, indicating that it has switched to synchronisation mode.

2. Within 10 seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

3. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Print

HOW TO SYNCHRONISE ET BLUE AND ET BLUE MIX ROLLING CODE REMOTE CONTROLS

ET BLUE and ET BLUE MIX remote control synchronisation can only be performed directly on the receiver itself.

Synchronising the remote control directly on the receiver

1. Press SET until “Pr9” appears on the display.

2. Browse the menu with the UP and DOWN buttons until “Lrn” appears on the display.

3. Press SET until “ch1” appears on the display.

4. Press the button on the remote control to be synchronised.

5. After being programmed, “dnE” will appear on the display.

6. To record more channels, press UP and DOWN until “ch2” or “ch3” appears on the display and press the button on the remote control to be synchronised.

7. To finish, press SET until “End” appears on the display.

Print

SYNCHRONISING AERF ROLLING CODE REMOTE CONTROLS

The JCM rolling code remote control synchronisation procedure is identical for all models, including customised models, except the 868 MHz.

There are two synchronisation procedures for these devices.

Remote synchronisation procedure using the original remote control

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the remote control already synchronised in the facility. If there is no rear button, press all the buttons on the original device at once.

The receiver will emit a beep, indicating that it has switched to synchronisation mode.

2. Within 10 seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

3. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Print

SYNCHRONISING APRIMATIC TXM ROLLING CODE REMOTE CONTROLS

Remote synchronisation procedure for the APRIMATIC TXM remote control

1. Stand near the receiver and press all the emission keys of the device already synchronised in the facility.

The receiver will emit a beep and the LED will flash.

2. Press the synch button of the duplicated device.

The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.

3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the original or duplicated remote control.

The LED and buzzer will turn off.

Direct synchronisation procedure for the APRIMATIC TXM remote control

1. Open the receiver and press the small button located near the LED for 2 seconds.

The receiver LED will flash

2. Press the synch button of the duplicated device.

The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.

3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the master remote control.

The LED and buzzer will turn off.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING APRIMATIC TXM ROLLING CODE REMOTE CONTROLS

Remote synchronisation procedure for the APRIMATIC TXM remote control

1. Stand near the receiver and press all the emission keys of the device already synchronised in the facility.

The receiver will emit a beep and the LED will flash.

2. Press the synch button of the duplicated device.

The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.

3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the original or duplicated remote control.

The LED and buzzer will turn off.

Direct synchronisation procedure for the APRIMATIC TXM remote control

1. Open the receiver and press the small button located near the LED for 2 seconds.

The receiver LED will flash

2. Press the synch button of the duplicated device.

The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.

3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the master remote control.

The LED and buzzer will turn off.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING APRIMATIC TXM ROLLING CODE REMOTE CONTROLS

Remote synchronisation procedure for the APRIMATIC TXM remote control

1. Stand near the receiver and press all the emission keys of the device already synchronised in the facility.

The receiver will emit a beep and the LED will flash.

2. Press the synch button of the duplicated device.

The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.

3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the original or duplicated remote control.

The LED and buzzer will turn off.

Direct synchronisation procedure for the APRIMATIC TXM remote control

1. Open the receiver and press the small button located near the LED for 2 seconds.

The receiver LED will flash

2. Press the synch button of the duplicated device.

The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.

3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the master remote control.

The LED and buzzer will turn off.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING JCM ROLLING CODE REMOTE CONTROLS

The JCM rolling code remote control synchronisation procedure is identical for all models except the 868 MHz.

There are 3 synchronisation procedures for these devices.

PIN-MODE remote synchronising procedure

The following procedure must be applied if the receiver bears the words PIN-MODE:

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the remote control to be synchronised.

The receiver will emit a long beep, indicating that the device has been successfully synchronised.

Remote synchronisation procedure using the original remote control

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the synchronised remote control.

The receiver will emit a beep, indicating that it has switched to synchronisation mode.

2. Within 10 seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer's permission.

3. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Direct synchronisation procedure on the receiver

1. Open the receiver and locate a switch or pushbutton labelled "PROG".

2. Press the button or turn on the switch.

The receiver will emit a long beep and the LED will light up. From this point, follow the previous procedure from step 2 above.

Print

SYNCHRONISING FAAC ROLLING CODE REMOTE CONTROLS

FAAC remote controls can be synchronised using a master remote control with its own code. In this case it is not necessary to work directly or remotely with the receiver.

Follow these steps to synchronise a slave remote control from a master device. This procedure is valid for the TML and 868 SLH series.

TML series

Warning: if you press the slave remote control first and then the master device you will delete the master codes.

1. Press the button of the already synchronised remote control and hold down.

2. Still holding down the master device button, press the same button on the slave with the two devices close to each other.

The LED on the slave will flash.

3. Repeat the operation for the remaining buttons.

SERIE 868SLH

Warning: if you press the slave remote control first and then the master device you will delete the master codes.

1. Press the two buttons on the master device until the LED starts flashing and release after one second (on devices with four buttons, press the top right and lower left buttons).

2. Before the master device LED stops flashing, press the top right button on the master device again with the remote controls close to each other. The master LED will change to steady.

3. Still holding down the master device button, press the same button on the slave.

The slave device LED will flash once to confirm that the code has been stored.

4. Release both buttons.