Print

SYNCHRONISING FAAC ROLLING CODE REMOTE CONTROLS

FAAC remote controls can be synchronised using a master remote control with its own code. In this case it is not necessary to work directly or remotely with the receiver.

Follow these steps to synchronise a slave remote control from a master device. This procedure is valid for the TML and 868 SLH series.

TML series

Warning: if you press the slave remote control first and then the master device you will delete the master codes.

1. Press the button of the already synchronised remote control and hold down.

2. Still holding down the master device button, press the same button on the slave with the two devices close to each other.

The LED on the slave will flash.

3. Repeat the operation for the remaining buttons.

SERIE 868SLH

Warning: if you press the slave remote control first and then the master device you will delete the master codes.

1. Press the two buttons on the master device until the LED starts flashing and release after one second (on devices with four buttons, press the top right and lower left buttons).

2. Before the master device LED stops flashing, press the top right button on the master device again with the remote controls close to each other. The master LED will change to steady.

3. Still holding down the master device button, press the same button on the slave.

The slave device LED will flash once to confirm that the code has been stored.

4. Release both buttons.

Print

HOW TO SYNCHRONISE STAGNOLI ROLLING CODE REMOTE CONTROLS

STAGNOLI remote control synchronisation can only be performed directly on the receiver itself.

Synchronising the remote control directly on the receiver:

During start-up, LED1 and LED2 will light up for two seconds as follows:

• LED1 on: Variable code programmed.

• LED2 on: Fixed code programmed.

• Both LEDs on: no transmitter in memory.

Once the receiver is powered up, press the synchronisation button (PG) a number of times corresponding to the operation you wish to complete, holding down the button on the last press.

Synchronisation of the first channel on the receiver: Press the synchronisation button (PG) twice and hold. LED1 will blink twice: press the transmitter button you wish to synchronise.

If the new code has been recognised and synchronised correctly, LED1 will emit a long flash.

By holding the synchronisation button (PG), it is possible to synchronise additional transmitters by pressing the buttons (one at a time) on the additional transmitters to be synchronised.

Synchronisation of the second channel on the receiver: Press the synchronisation button (PG) three times and hold. LED1 will blink three times: press the transmitter button you wish to synchronise.

If the new code has been recognised and synchronised correctly, LED1 will emit a long flash.

By holding the synchronisation button (PG), it is possible to synchronise additional transmitters by pressing the buttons (one at a time) on the additional transmitters to be synchronised.

Print

SYNCHRONISING SEAV ROLLING CODE REMOTE CONTROLS

Remote synchronisation procedure for the SEAV remote control

1. Stand near the receiver and press the first desired channel on the already synchronised remote control for 15 seconds.

The receiver LED will begin to flash while it is waiting for transmission of a code.

2. Press the button for the same channel on the remote control to be synchronised.

The receiver LED will light up steady, indicating that the channel has been synchronised.

Repeat the operation for the remaining buttons.

Direct synchronisation procedure for the SEAV remote control

1. Open the receiver and press the button marked SEL.

The CODE CH1 LED will begin to flash while it is waiting for transmission of a code.

2. Press the button for the same channel on the remote control to be synchronised.

The receiver LED will light up steady, indicating that the channel has been synchronised.

Repeat the same process for the second channel but pressing the SEL button twice (the CODE CH2 LED will flash) and pressing the second button on the duplicated device.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING FADINI ROLLING CODE REMOTE CONTROLS

FADINI remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.

Remote synchronisation procedure

1. Press buttons 1 and 2 simultaneously on the new remote control and hold for 10 seconds.

2. Release, and before 15 seconds elapse press buttons 1 and 2 of the device already synchronised in the facility and hold for at least 10 seconds.

3. Finally, press any button of the device to be synchronised.

Direct synchronisation procedure on the receiver

1. In the receiver, use a jumper to bypass C1.

2. Press button P in the receiver and button 1 on the remote control to be synchronised for 5 seconds.

3. Release the buttons on both devices and remove the jumper.

4. Repeat the operation for all channels, bypassing the relevant channel each time (C2, C3 and C4).

Print

SYNCHRONISING NOVOFERM ROLLING CODE REMOTE CONTROLS

The Novoferm remote control can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver

1. Open the receiver and press the button located inside until the LED begins to flash.

2. Then press the button on the remote control and hold for approximately 3 seconds until the LED begins to flash quickly.

Take the following steps if the facility has a ceiling-mounted motor.

Print

SYNCHRONISING FADINI ROLLING CODE REMOTE CONTROLS

FADINI remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.

Remote synchronisation procedure

1. Press buttons 1 and 2 simultaneously on the new remote control and hold for 10 seconds.

2. Release, and before 15 seconds elapse press buttons 1 and 2 of the device already synchronised in the facility and hold for at least 10 seconds.

3. Finally, press any button of the device to be synchronised.

Direct synchronisation procedure on the receiver

1. In the receiver, use a jumper to bypass C1.

2. Press button P in the receiver and button 1 on the remote control to be synchronised for 5 seconds.

3. Release the buttons on both devices and remove the jumper.

4. Repeat the operation for all channels, bypassing the relevant channel each time (C2, C3 and C4).