Print

SYNCHRONISING KEY ROLLING CODE REMOTE CONTROLS

KEY remote controls can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver (type A receiver)

1. Press button S on the receiver.

2. The LED (Ir1) will light up.

3. Release button S and press button P.

4. The LED (Ir1) will flash once.

5. Release the button.

6. Press the button of the remote control to be synchronised until the LED (Ir1) begins to flash, then release.

7. Wait for 10 seconds for the receiver to exit synchronisation mode.

Direct synchronisation procedure on the receiver (type B receiver)

1. Press KEY the same number of times as the channel you wish to synchronise (one time for channel 1, two times for channel 2, etc.).

2. The LED will flash the number of times equal to the number of the selected channel.

3. Within the next 7 seconds, press the button on the remote control to be synchronised for 2 seconds.4. The LED will flash once if synchronisation has been successful.

5. Repeat step 3 if you wish to add more remote controls.

Print

SYNCHRONISING GIBIDI ROLLING CODE REMOTE CONTROLS

Direct synchronisation procedure on the receiver

1. Open the receiver and locate the programming button on the circuit board.

2. Press it briefly.

The receiver LED will flash.

3. Within 10 seconds, press the button of the remote control you wish to synchronise.

The receiver will automatically exit synchronisation mode after a short time.

Print

SYNCHRONISING V2 ROLLING CODE REMOTE CONTROLS

V2 remote controls can be synchronised either remotely or directly on the receiver.

Remote synchronising procedure

1. Press buttons 1 and 2 on the remote control to be synchronised simultaneously for approximately 10 seconds.

2. Release.

3. Within 5 seconds, press any other button on the device to be synchronised.

4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.

The code has been stored.

Since this option is not enabled on all models we recommend the following procedure.

Direct synchronisation procedure on the receiver

1. Open the receiver and locate the small SW1 button.

2. Press until the receiver LED lights up.

3. Within 5 seconds, press the button on the remote control to be synchronised and hold until the receiver LED blinks.

4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.

The code has been stored.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING BFT ROLLING CODE REMOTE CONTROLS

The receivers of these models enable remote or direct synchronisation.

Remote synchronisation procedure for the BFT MITTO remote control

1. Stand near the receiver and press the hidden button at the rear of the BFT original remote control for 2 seconds.

2. Press the left button on the front of the original remote control for 2 seconds.

3. Press the synch button on the rear of the device to be synchronised.

4. Finally, press the first button on the device to be synchronised.

Remote synchronisation procedure for the BFT TRC or MITTO remote control

1. Open the receiver and locate the SW-1 and SW-2 buttons. Press the first (SW-1).

A flashing LED should light up in the receiver.

2. Open the battery cover of the already synchronised remote control or the one you have copied and press the button inside.

The receiver light should change to steady.

3. Press the button of the device to be synchronised.

The light on the receiver will return to flashing and turn off after 30 seconds, indicating that the synchronisation process has finished.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING FADINI ROLLING CODE REMOTE CONTROLS

FADINI remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.

Remote synchronisation procedure

1. Press buttons 1 and 2 simultaneously on the new remote control and hold for 10 seconds.

2. Release, and before 15 seconds elapse press buttons 1 and 2 of the device already synchronised in the facility and hold for at least 10 seconds.

3. Finally, press any button of the device to be synchronised.

Direct synchronisation procedure on the receiver

1. In the receiver, use a jumper to bypass C1.

2. Press button P in the receiver and button 1 on the remote control to be synchronised for 5 seconds.

3. Release the buttons on both devices and remove the jumper.

4. Repeat the operation for all channels, bypassing the relevant channel each time (C2, C3 and C4).