Print

SYNCHRONISING GO ROLLING CODE REMOTE CONTROLS

The GO remote control is synchronised directly with the receiver the first time the button is pressed. However, this option is disabled on some models, which must be synchronised manually.

GO remote control manual synchronisation procedure

1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".

2. Press the button or turn on the switch.

3. Within ten (10) seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

4. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING BFT ROLLING CODE REMOTE CONTROLS

The receivers of these models enable remote or direct synchronisation.

Remote synchronisation procedure for the BFT MITTO remote control

1. Stand near the receiver and press the hidden button at the rear of the BFT original remote control for 2 seconds.

2. Press the left button on the front of the original remote control for 2 seconds.

3. Press the synch button on the rear of the device to be synchronised.

4. Finally, press the first button on the device to be synchronised.

Remote synchronisation procedure for the BFT TRC or MITTO remote control

1. Open the receiver and locate the SW-1 and SW-2 buttons. Press the first (SW-1).

A flashing LED should light up in the receiver.

2. Open the battery cover of the already synchronised remote control or the one you have copied and press the button inside.

The receiver light should change to steady.

3. Press the button of the device to be synchronised.

The light on the receiver will return to flashing and turn off after 30 seconds, indicating that the synchronisation process has finished.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING GO ROLLING CODE REMOTE CONTROLS

The GO remote control is synchronised directly with the receiver the first time the button is pressed. However, this option is disabled on some models, which must be synchronised manually.

GO remote control manual synchronisation procedure

1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".

2. Press the button or turn on the switch.

3. Within ten (10) seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

4. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING GIBIDI ROLLING CODE REMOTE CONTROLS

Direct synchronisation procedure on the receiver

1. Open the receiver and locate the programming button on the circuit board.

2. Press it briefly.

The receiver LED will flash.

3. Within 10 seconds, press the button of the remote control you wish to synchronise.

The receiver will automatically exit synchronisation mode after a short time.

Print

SYNCHRONISING FAAC ROLLING CODE REMOTE CONTROLS

FAAC remote controls can be synchronised using a master remote control with its own code. In this case it is not necessary to work directly or remotely with the receiver.

Follow these steps to synchronise a slave remote control from a master device. This procedure is valid for the TML and 868 SLH series.

TML series

Warning: if you press the slave remote control first and then the master device you will delete the master codes.

1. Press the button of the already synchronised remote control and hold down.

2. Still holding down the master device button, press the same button on the slave with the two devices close to each other.

The LED on the slave will flash.

3. Repeat the operation for the remaining buttons.

SERIE 868SLH

Warning: if you press the slave remote control first and then the master device you will delete the master codes.

1. Press the two buttons on the master device until the LED starts flashing and release after one second (on devices with four buttons, press the top right and lower left buttons).

2. Before the master device LED stops flashing, press the top right button on the master device again with the remote controls close to each other. The master LED will change to steady.

3. Still holding down the master device button, press the same button on the slave.

The slave device LED will flash once to confirm that the code has been stored.

4. Release both buttons.

Print

SYNCHRONISING LIFT MASTER ROLLING CODE REMOTE CONTROLS

The Lift Master remote control can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver

1. Press the button on the remote control and hold.

2. Press and release the Learn button for channel A on the receiver.

3. The control LED will flash once.

4. Release the remote control button.

If you release the remote control button before the control LED flashes the receiver will not accept the code.

Repeat this procedure for any other devices you wish to add.

If you are using a second door, select another button on the remote control and repeat the steps for channel B.

Print

SYNCHRONISING GO ROLLING CODE REMOTE CONTROLS

The GO remote control is synchronised directly with the receiver the first time the button is pressed. However, this option is disabled on some models, which must be synchronised manually.

GO remote control manual synchronisation procedure

1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".

2. Press the button or turn on the switch.

3. Within ten (10) seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

4. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

HOW TO SYNCHRONISE KING GATES STYLO ROLLING CODE REMOTE CONTROLS

Direct synchronisation procedure on the receiver:

1. Open the receiver and locate the programming button on the circuit board.

2. Hold the button for two seconds.

The receiver LED will switch on.

3. Press the button of the remote control you wish to synchronise within 10 seconds.

The receiver will automatically exit synchronisation mode after a short time.