Print

SYNCHRONISING SKYMASTER ROLLING CODE REMOTE CONTROLS

SKYMASTER remote controls can only be synchronised directly on the receiver. The process is as follows.

Synchronisation procedure on the receiver

1. Press the CODE button once.

The red LED will begin the flash.

2. Press the button on the remote control to be synchronised twice.

The red LED will change to steady and then turn off.

3. Repeat the operation for every button (channel) and every device you wish to synchronise.

If the remote control being synchronised is the first one, you will have to delete the memory as follows:

1. Press and hold the CODE button for 8 seconds during which the LED will remain steady

2. The red LED will turn of and the memory will be deleted.

Print

SYNCHRONISING JCM ROLLING CODE REMOTE CONTROLS

The JCM rolling code remote control synchronisation procedure is identical for all models except the 868 MHz.

There are 3 synchronisation procedures for these devices.

PIN-MODE remote synchronising procedure

The following procedure must be applied if the receiver bears the words PIN-MODE:

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the remote control to be synchronised.

The receiver will emit a long beep, indicating that the device has been successfully synchronised.

Remote synchronisation procedure using the original remote control

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the synchronised remote control.

The receiver will emit a beep, indicating that it has switched to synchronisation mode.

2. Within 10 seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

3. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Direct synchronisation procedure on the receiver

1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".

2. Press the button or turn on the switch.

The receiver will emit a long beep and the LED will light up. From this point, follow the previous procedure from step 2 above.

Print

SYNCHRONISING SKYMASTER ROLLING CODE REMOTE CONTROLS

SKYMASTER remote controls can only be synchronised directly on the receiver. The process is as follows.

Synchronisation procedure on the receiver

1. Press the CODE button once.

The red LED will begin the flash.

2. Press the button on the remote control to be synchronised twice.

The red LED will change to steady and then turn off.

3. Repeat the operation for every button (channel) and every device you wish to synchronise.

If the remote control being synchronised is the first one, you will have to delete the memory as follows:

1. Press and hold the CODE button for 8 seconds during which the LED will remain steady

2. The red LED will turn of and the memory will be deleted.

Print

SYNCHRONISING MHOUSE ROLLING CODE REMOTE CONTROLS

MHOUSE remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.

Remote synchronisation procedure (identical to procedure for NICE, Smilo and Flo-R devices)

1. Press and hold the button on the device you wish to synchronise for at least 5 seconds and then release.

2. Slowly press the button on the previously-synchronised remote control 3 times.

3. Slowly press the button on the device to be synchronised once.

Direct synchronisation procedure on the receiver

1. Press button P1 on the receiver and hold for at least 3 seconds.

2. Release the button when LED P1 lights up.

3. You have 10 seconds to press any button on the device to be synchronised for at least 2 seconds. LED P1 will flash 3 times if synchronisation has been performed successfully.

4. If you wish to synchronise additional remote controls, repeat step 2 within 10 seconds or the receiver will automatically exit synchronisation mode.

Print

SYNCHRONISING LIFT MASTER ROLLING CODE REMOTE CONTROLS

The Lift Master remote control can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver

1. Press the button on the remote control and hold.

2. Press and release the Learn button for channel A on the receiver.

3. The control LED will flash once.

4. Release the remote control button.

If you release the remote control button before the control LED flashes the receiver will not accept the code.

Repeat this procedure for any other devices you wish to add.

If you are using a second door, select another button on the remote control and repeat the steps for channel B.