Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
CARDIN® S438 TX Remote
- F 433,92
- C FIX CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
FADINI® ASTRO 78A Remote
SKY MASTER® MHZ Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING SKYMASTER ROLLING CODE REMOTE CONTROLS
SKYMASTER remote controls can only be synchronised directly on the receiver. The process is as follows.
Synchronisation procedure on the receiver
1. Press the CODE button once.
The red LED will begin the flash.
2. Press the button on the remote control to be synchronised twice.
The red LED will change to steady and then turn off.
3. Repeat the operation for every button (channel) and every device you wish to synchronise.
If the remote control being synchronised is the first one, you will have to delete the memory as follows:
1. Press and hold the CODE button for 8 seconds during which the LED will remain steady
2. The red LED will turn of and the memory will be deleted.
O&O® T.COM R8 Remote
FADINI® ASTRO 433 Remote
- F 433,92
- C FIX CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
O&O® RAY 2-4 Remote
SERAI® OG28 Remote
ELVOX® ERT 1 Remote
- F 433,92
- C ROLLING CODE
- B 4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
HOW TO SYNCHRONISE ELVOX ROLLING CODE REMOTE CONTROLS
ELVOX remote control synchronisation can only be performed directly on the receiver itself.
Synchronising the remote control directly on the receiver
Sliding and hinged doors
1. Hold the button on the receiver I2(P2).
2. While still holding the button on the receiver, press the button on the remote control to be synchronised.
3. Wait for the LED to flash, confirming the synchronisation.
4. Release both buttons.
ECRU receiver
1. Hold the button on the P1 receiver for two seconds. The DL1 LED will flash green.
2. Release the P1 button on the receiver.
3. Press button 1 on the remote control to be programmed.
4. The blue DL5 LED will flash.
5. On pressing the P1 button again for two seconds, the DL2 LED will flash green to synchronise channel 2.
6. Press button 2 on the remote control to be programmed.
7. The blue DL5 LED will flash.
8. To synchronise buttons 3 and 4, repeat steps 5 to 7. The LEDs DL3 and DL4 will light. Press buttons 3 and 4 in each case.
9. To leave synchronisation mode, press buttons P1 and P2 when the green LED flashes while waiting for a signal.
TELCOMA® NOIRE Remote
KEY® PLAY4R Remote
ERREKA® CYJC Remote
- F 290
- C FIX CODE
- B 1,2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
ALLTRONIC® S-425 Remote
- F 433,92
- C FIX CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
NOVOFERM® NOVOTRON Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING NOVOFERM ROLLING CODE REMOTE CONTROLS
The Novoferm remote control can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver
1. Open the receiver and press the button located inside until the LED begins to flash.
2. Then press the button on the remote control and hold for approximately 3 seconds until the LED begins to flash quickly.
Take the following steps if the facility has a ceiling-mounted motor.
The selected remotes can not be copied with a single JMA remote