Print

SYNCHRONISING GO ROLLING CODE REMOTE CONTROLS

The GO remote control is synchronised directly with the receiver the first time the button is pressed. However, this option is disabled on some models, which must be synchronised manually.

GO remote control manual synchronisation procedure

1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".

2. Press the button or turn on the switch.

3. Within ten (10) seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

4. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING NOVOFERM ROLLING CODE REMOTE CONTROLS

The Novoferm remote control can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver

1. Open the receiver and press the button located inside until the LED begins to flash.

2. Then press the button on the remote control and hold for approximately 3 seconds until the LED begins to flash quickly.

Take the following steps if the facility has a ceiling-mounted motor.

Print

SYNCHRONISING BFT ROLLING CODE REMOTE CONTROLS

The receivers of these models enable remote or direct synchronisation.

Remote synchronisation procedure for the BFT MITTO remote control

1. Stand near the receiver and press the hidden button at the rear of the BFT original remote control for 2 seconds.

2. Press the left button on the front of the original remote control for 2 seconds.

3. Press the synch button on the rear of the device to be synchronised.

4. Finally, press the first button on the device to be synchronised.

Remote synchronisation procedure for the BFT TRC or MITTO remote control

1. Open the receiver and locate the SW-1 and SW-2 buttons. Press the first (SW-1).

A flashing LED should light up in the receiver.

2. Open the battery cover of the already synchronised remote control or the one you have copied and press the button inside.

The receiver light should change to steady.

3. Press the button of the device to be synchronised.

The light on the receiver will return to flashing and turn off after 30 seconds, indicating that the synchronisation process has finished.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING SOMMER ROLLING CODE REMOTE CONTROLS

SOMMER remote control can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver

1. Press button B on the receiver

a. Once for channel 1. LED (C1) will light up.

b. Twice for channel 2. LED (C2) will light up.

The receiver will exit synchronisation mode if no code is transmitted during a period of 10 seconds.

To exit synchronisation mode, press key B several times until all LEDs have turned off.

2. Press the desired button (D) on the remote control. The transmitter will send the radio code to the receiver.

The LED for the selected channel will flash and switch off.

Repeat Steps 1 and 2 to synchronise additional transmitters with this receiver.

Print

SYNCHRONISING KEY ROLLING CODE REMOTE CONTROLS

KEY remote controls can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver (type A receiver)

1. Press button S on the receiver.

2. The LED (Ir1) will light up.

3. Release button S and press button P.

4. The LED (Ir1) will flash once.

5. Release the button.

6. Press the button of the remote control to be synchronised until the LED (Ir1) begins to flash, then release.

7. Wait for 10 seconds for the receiver to exit synchronisation mode.

Direct synchronisation procedure on the receiver (type B receiver)

1. Press KEY the same number of times as the channel you wish to synchronise (one time for channel 1, two times for channel 2, etc.).

2. The LED will flash the number of times equal to the number of the selected channel.

3. Within the next 7 seconds, press the button on the remote control to be synchronised for 2 seconds.4. The LED will flash once if synchronisation has been successful.

5. Repeat step 3 if you wish to add more remote controls.