Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
CASIT® BE HAPPY RS Remote
- F 433,92
- C ROLLING CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING SEAV ROLLING CODE REMOTE CONTROLS
Remote synchronisation procedure for the SEAV remote control
1. Stand near the receiver and press the first desired channel on the already synchronised remote control for 15 seconds.
The receiver LED will begin to flash while it is waiting for transmission of a code.
2. Press the button for the same channel on the remote control to be synchronised.
The receiver LED will light up steady, indicating that the channel has been synchronised.
Repeat the operation for the remaining buttons.
Direct synchronisation procedure for the SEAV remote control
1. Open the receiver and press the button marked SEL.
The CODE CH1 LED will begin to flash while it is waiting for transmission of a code.
2. Press the button for the same channel on the remote control to be synchronised.
The receiver LED will light up steady, indicating that the channel has been synchronised.
Repeat the same process for the second channel but pressing the SEL button twice (the CODE CH2 LED will flash) and pressing the second button on the duplicated device.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
CLEMSA® DIGICODE MH Remote
- F 433,92
- C FIX CODE
- B 1,2,3
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
BREDA® TOP 432 Remote
- F 433,92
- C FIX CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
CLEMSA® MASTERCODE MV Remote
- F 433,92
- C FIX CODE
- B 1,2,3
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
TELCOMA® NOIRE Remote
SOMFY® KEYTIS RTS NS Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING SOMFY ROLLING CODE REMOTE CONTROLS
SOMFY remote control can only be synchronised directly on the external receiver and remotely on the integrated shutter receiver. A distinction must be made between SOMFY and TELIS remote controls.
Synchronisation procedure on the receiver
External receiver
1. Press and hold the \"Prog\" button on the receiver for 2 seconds. The red LED on the receiver will remain lit.
Internal receiver (Telis)
1. Press and hold the up and down buttons on the Telis remote control for 2 seconds. The red LED on the receiver will remain lit.
Keytis remote control
2. Press the button of the device to be synchronised. The LED on the receiver will flash.
3. Wait until the LED turns off.
Telis 1RTS remote control
2. Press the rear button on the remote control for half a second. The LED on the receiver will flash.
3. Wait until the LED turns off.
Telis 4 RTS remote control
2. Press the channel selection button until the LED for the desired channel lights up.
3. Press the rear button on the remote control for half a second. The LED on the receiver will flash.
4. Wait until the LED turns off.
DEA SYSTEM® DEA306 Remote
- F 306
- C FIX CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
LIFT MASTER® 94335E/EML Remote
- F 433,92
- C ROLLING CODE
- B 3
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING LIFT MASTER ROLLING CODE REMOTE CONTROLS
The Lift Master remote control can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver
1. Press the button on the remote control and hold.
2. Press and release the Learn button for channel A on the receiver.
3. The control LED will flash once.
4. Release the remote control button.
If you release the remote control button before the control LED flashes the receiver will not accept the code.
Repeat this procedure for any other devices you wish to add.
If you are using a second door, select another button on the remote control and repeat the steps for channel B.
WAYNE DALTON® S425 Remote
- F 433,92
- C FIX CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
The selected remotes can not be copied with a single JMA remote