Print

SYNCHRONISING CAME ROLLING CODE REMOTE CONTROLS

CAME ATO remote controls can be synchronised either directly or remotely by taking the following steps.

Synchronisation procedure using the receiver

1. Press the button of the desired channel on the receiver for 2 seconds.

2. The LED on the receiver will flash.

3. Press the button of the same channel on the remote control to be synchronised. Press the button for the same channel on each remote control in turn if you wish to synchronise more than one device.

4. The LED on the receiver will change to steady each time a button is pressed.

5. Repeat the process for the other channel.

Remote synchronising procedure

1. Press the button of the desired channel on the remote control for 15 seconds.

2. The LED on the receiver will flash.

3. Press the button of the same channel on the remote control to be synchronised. Press the button for the same channel on each remote control in turn if you wish to synchronise more than one device.

4. The LED on the receiver will change to steady each time a button is pressed.

Print

HOW TO SYNCHRONISE ET BLUE AND ET BLUE MIX ROLLING CODE REMOTE CONTROLS

ET BLUE and ET BLUE MIX remote control synchronisation can only be performed directly on the receiver itself.

Synchronising the remote control directly on the receiver

1. Press SET until “Pr9” appears on the display.

2. Browse the menu with the UP and DOWN buttons until “Lrn” appears on the display.

3. Press SET until “ch1” appears on the display.

4. Press the button on the remote control to be synchronised.

5. After being programmed, “dnE” will appear on the display.

6. To record more channels, press UP and DOWN until “ch2” or “ch3” appears on the display and press the button on the remote control to be synchronised.

7. To finish, press SET until “End” appears on the display.

Print

SYNCHRONISING BFT ROLLING CODE REMOTE CONTROLS

The receivers of these models enable remote or direct synchronisation.

Remote synchronisation procedure for the BFT MITTO remote control

1. Stand near the receiver and press the hidden button at the rear of the BFT original remote control for 2 seconds.

2. Press the left button on the front of the original remote control for 2 seconds.

3. Press the synch button on the rear of the device to be synchronised.

4. Finally, press the first button on the device to be synchronised.

Remote synchronisation procedure for the BFT TRC or MITTO remote control

1. Open the receiver and locate the SW-1 and SW-2 buttons. Press the first (SW-1).

A flashing LED should light up in the receiver.

2. Open the battery cover of the already synchronised remote control or the one you have copied and press the button inside.

The receiver light should change to steady.

3. Press the button of the device to be synchronised.

The light on the receiver will return to flashing and turn off after 30 seconds, indicating that the synchronisation process has finished.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

SYNCHRONISING BENINCA ROLLING CODE REMOTE CONTROLS

Remote synchronisation procedure for the BENINCA remote control

1. Stand near the receiver and press the already synchronised hidden transmitter key.

2. Within 5 seconds press the key on the already synchronised remote control that corresponds to the channel to be associated with the new device.

3. Within 5 seconds, press the key of the new device to be associated with the channel selected in step 2.

The receiver will memorise the new transmitter and exit synchronisation mode immediately.

Direct synchronisation procedure for the BENINCA remote control

1. Open the receiver and briefly press the P button.

The red LED on the receiver will light up for 3 seconds, turn off for 1 second and light up for a further 5 seconds.

2. While the red LED is lit up, press the transmitter button that you want to synchronise with channel 1.

Other transmitters can also be entered. You only have to press a key before 5 seconds elapse since the previous device was synchronised.

3. Once finished, wait 5 seconds until the receiver exits synchronisation mode.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

Print

HOW TO SYNCHRONISE CENTURION ROLLING CODE REMOTE CONTROLS

CENTURION remote control synchronisation can only be performed directly or via radio if you own a MASTER remote control or a VOYAGE receiver.

NOVA and SMART Receiver

Synchronising the remote control directly on the receiver

1. Switch the jumper to the LEARN position.

2. The LED will light up red.

3. Press the button on the remote control to be recorded. The LED will flash.

4. Remove the jumper and leave it disconnected.

NOVA VOYAGE Receiver

Synchronising the remote control directly on the receiver

1. Switch the jumper to the LEARN position.

2. The LED will light up red.

3. Press the button on the remote control to be recorded. The LED will flash.

4. Remove the jumper and leave it disconnected.

The first transmitter synchronised will be the MASTER remote control.

Remotely synchronising the remote control on the receiver with a MASTER remote control

A MASTER remote control is needed for remote synchronisation. The MASTER remote control is the first remote control that is synchronised when the receiver is empty.

1. Press any button on the MASTER remote control for 10 seconds or until the LED flashes 10 times.

2. The LED will light up red.

3. Press the button on the remote control to be recorded.

4. Wait 10 seconds for the receiver to leave synchronisation mode.

Print

SYNCHRONISING JCM ROLLING CODE REMOTE CONTROLS

The JCM rolling code remote control synchronisation procedure is identical for all models except the 868 MHz.

There are 3 synchronisation procedures for these devices.

PIN-MODE remote synchronising procedure

The following procedure must be applied if the receiver bears the words PIN-MODE:

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the remote control to be synchronised.

The receiver will emit a long beep, indicating that the device has been successfully synchronised.

Remote synchronisation procedure using the original remote control

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the synchronised remote control.

The receiver will emit a beep, indicating that it has switched to synchronisation mode.

2. Within 10 seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

3. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Direct synchronisation procedure on the receiver

1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".

2. Press the button or turn on the switch.

The receiver will emit a long beep and the LED will light up. From this point, follow the previous procedure from step 2 above.