Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
SIMINOR® S224 Remote
SIMINOR® EM47 Remote
SIMINOR® MITTO Remote
SIMINOR® S38 Remote
CRAWFORD® EA433K Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING CRAWFORD/NORMSTHAL ROLLING CODE REMOTE CONTROLS
CRAWFORD/NORMSTHAL remote controls can only be synchronised directly on the receiver by taking the following steps.
Synchronisation procedure using the receiver
1. Press the SET button:
Once for impulse response (the receiver is active while the button is being held)
Twice for flip-flop response (the receiver is active until the next time it is pressed)
Three times for ON
Four times for OFF
2. Press the button of the device to be synchronised
3. The LED will flash, indicating that the code has been stored.
SIMINOR® CVXNL Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING SOMFY ROLLING CODE REMOTE CONTROLS
SOMFY remote control can only be synchronised directly on the external receiver and remotely on the integrated shutter receiver. A distinction must be made between SOMFY and TELIS remote controls.
Synchronisation procedure on the receiver
External receiver
1. Press and hold the \"Prog\" button on the receiver for 2 seconds. The red LED on the receiver will remain lit.
Internal receiver (Telis)
1. Press and hold the up and down buttons on the Telis remote control for 2 seconds. The red LED on the receiver will remain lit.
Keytis remote control
2. Press the button of the device to be synchronised. The LED on the receiver will flash.
3. Wait until the LED turns off.
Telis 1RTS remote control
2. Press the rear button on the remote control for half a second. The LED on the receiver will flash.
3. Wait until the LED turns off.
Telis 4 RTS remote control
2. Press the channel selection button until the LED for the desired channel lights up.
3. Press the rear button on the remote control for half a second. The LED on the receiver will flash.
4. Wait until the LED turns off.
V2® HANDY Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING V2 ROLLING CODE REMOTE CONTROLS
V2 remote controls can be synchronised either remotely or directly on the receiver.
Remote synchronising procedure
1. Press buttons 1 and 2 on the remote control to be synchronised simultaneously for approximately 10 seconds.
2. Release.
3. Within 5 seconds, press any other button on the device to be synchronised.
4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.
The code has been stored.
Since this option is not enabled on all models we recommend the following procedure.
Direct synchronisation procedure on the receiver
1. Open the receiver and locate the small SW1 button.
2. Press until the receiver LED lights up.
3. Within 5 seconds, press the button on the remote control to be synchronised and hold until the receiver LED blinks.
4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.
The code has been stored.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
V2® TDR Remote
- F 433,92
- C FIX CODE
- B 1,2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
V2® TNQ Remote
The selected remotes can not be copied with a single JMA remote