Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
CASALI® JA33 AMIGO Remote
- F 868,3
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-48
SYNCHRONISING FAAC ROLLING CODE REMOTE CONTROLS
FAAC remote controls can be synchronised using a master remote control with its own code. In this case it is not necessary to work directly or remotely with the receiver.
Follow these steps to synchronise a slave remote control from a master device. This procedure is valid for the TML and 868 SLH series.
TML series
Warning: if you press the slave remote control first and then the master device you will delete the master codes.
1. Press the button of the already synchronised remote control and hold down.
2. Still holding down the master device button, press the same button on the slave with the two devices close to each other.
The LED on the slave will flash.
3. Repeat the operation for the remaining buttons.
SERIE 868SLH
Warning: if you press the slave remote control first and then the master device you will delete the master codes.
1. Press the two buttons on the master device until the LED starts flashing and release after one second (on devices with four buttons, press the top right and lower left buttons).
2. Before the master device LED stops flashing, press the top right button on the master device again with the remote controls close to each other. The master LED will change to steady.
3. Still holding down the master device button, press the same button on the slave.
The slave device LED will flash once to confirm that the code has been stored.
4. Release both buttons.
V2® Match Remote
- F 433,92
- C ROLLING CODE
- B 4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING V2 ROLLING CODE REMOTE CONTROLS
V2 remote controls can be synchronised either remotely or directly on the receiver.
Remote synchronising procedure
1. Press buttons 1 and 2 on the remote control to be synchronised simultaneously for approximately 10 seconds.
2. Release.
3. Within 5 seconds, press any other button on the device to be synchronised.
4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.
The code has been stored.
Since this option is not enabled on all models we recommend the following procedure.
Direct synchronisation procedure on the receiver
1. Open the receiver and locate the small SW1 button.
2. Press until the receiver LED lights up.
3. Within 5 seconds, press the button on the remote control to be synchronised and hold until the receiver LED blinks.
4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.
The code has been stored.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
DELMA® MIZ-300 Remote
- F 300
- C FIX CODE
- B 1,2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
Europe Automatisme® ASMY Remote
- F 306
- C FIX CODE
- B 1,2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
CASIT® BE HAPPY S Remote
- F 433,92
- C FIX CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING SEAV ROLLING CODE REMOTE CONTROLS
Remote synchronisation procedure for the SEAV remote control
1. Stand near the receiver and press the first desired channel on the already synchronised remote control for 15 seconds.
The receiver LED will begin to flash while it is waiting for transmission of a code.
2. Press the button for the same channel on the remote control to be synchronised.
The receiver LED will light up steady, indicating that the channel has been synchronised.
Repeat the operation for the remaining buttons.
Direct synchronisation procedure for the SEAV remote control
1. Open the receiver and press the button marked SEL.
The CODE CH1 LED will begin to flash while it is waiting for transmission of a code.
2. Press the button for the same channel on the remote control to be synchronised.
The receiver LED will light up steady, indicating that the channel has been synchronised.
Repeat the same process for the second channel but pressing the SEL button twice (the CODE CH2 LED will flash) and pressing the second button on the duplicated device.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
Europe Automatisme® AKMY Remote
V2® TPQ-AF Remote
The selected remotes can not be copied with a single JMA remote