Legend: Click on the symbols for further information

Frequency

Type of code

  1. Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
  2. Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.

Buttons

Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.

PROCESS:

  1. In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
  2. Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.

If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.

Copy

No copy

EMFA® GO Remote

Remove Remote
  • F 868,3
  • C ROLLING CODE
  • B 2,4
  • AP NO
  • BT Slim / M-BT Advance / SR-48
EMFA® GO

Synchronising intructions

Print

SYNCHRONISING GO ROLLING CODE REMOTE CONTROLS

The GO remote control is synchronised directly with the receiver the first time the button is pressed. However, this option is disabled on some models, which must be synchronised manually.

GO remote control manual synchronisation procedure

1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".

2. Press the button or turn on the switch.

3. Within ten (10) seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

4. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

ALLMATIC® BROWN Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 1,2,4
  • AP YES
  • BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
ALLMATIC® BROWN

Synchronising intructions

Print

SYNCHRONISING BENINCA ROLLING CODE REMOTE CONTROLS

Remote synchronisation procedure for the BENINCA remote control

1. Stand near the receiver and press the already synchronised hidden transmitter key.

2. Within 5 seconds press the key on the already synchronised remote control that corresponds to the channel to be associated with the new device.

3. Within 5 seconds, press the key of the new device to be associated with the channel selected in step 2.

The receiver will memorise the new transmitter and exit synchronisation mode immediately.

Direct synchronisation procedure for the BENINCA remote control

1. Open the receiver and briefly press the P button.

The red LED on the receiver will light up for 3 seconds, turn off for 1 second and light up for a further 5 seconds.

2. While the red LED is lit up, press the transmitter button that you want to synchronise with channel 1.

Other transmitters can also be entered. You only have to press a key before 5 seconds elapse since the previous device was synchronised.

3. Once finished, wait 5 seconds until the receiver exits synchronisation mode.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

ROPER® GO Remote

Remove Remote
  • F 868,3
  • C ROLLING CODE
  • B 2,4
  • AP YES
  • BT Slim / M-BT Advance / SR-48
ROPER® GO

Synchronising intructions

Print

SYNCHRONISING GO ROLLING CODE REMOTE CONTROLS

The GO remote control is synchronised directly with the receiver the first time the button is pressed. However, this option is disabled on some models, which must be synchronised manually.

GO remote control manual synchronisation procedure

1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".

2. Press the button or turn on the switch.

3. Within ten (10) seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

4. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

TAU® 250K SLIM Remote

Remove Remote
  • F 433,92
  • C FIX CODE
  • B 2
  • AP NO
  • BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
TAU® 250K SLIM

SKY MASTER® MHZ00 Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 2,4
  • AP NO
SKY MASTER® MHZ00

Synchronising intructions

Print

SYNCHRONISING SKYMASTER ROLLING CODE REMOTE CONTROLS

SKYMASTER remote controls can only be synchronised directly on the receiver. The process is as follows.

Synchronisation procedure on the receiver

1. Press the CODE button once.

The red LED will begin the flash.

2. Press the button on the remote control to be synchronised twice.

The red LED will change to steady and then turn off.

3. Repeat the operation for every button (channel) and every device you wish to synchronise.

If the remote control being synchronised is the first one, you will have to delete the memory as follows:

1. Press and hold the CODE button for 8 seconds during which the LED will remain steady

2. The red LED will turn of and the memory will be deleted.

The selected remotes can not be copied with a single JMA remote