Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
FADINI® ASTRO 78A Remote
GENIUS® AMIGO Remote
- F 868,3
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING FAAC ROLLING CODE REMOTE CONTROLS
FAAC remote controls can be synchronised using a master remote control with its own code. In this case it is not necessary to work directly or remotely with the receiver.
Follow these steps to synchronise a slave remote control from a master device. This procedure is valid for the TML and 868 SLH series.
TML series
Warning: if you press the slave remote control first and then the master device you will delete the master codes.
1. Press the button of the already synchronised remote control and hold down.
2. Still holding down the master device button, press the same button on the slave with the two devices close to each other.
The LED on the slave will flash.
3. Repeat the operation for the remaining buttons.
SERIE 868SLH
Warning: if you press the slave remote control first and then the master device you will delete the master codes.
1. Press the two buttons on the master device until the LED starts flashing and release after one second (on devices with four buttons, press the top right and lower left buttons).
2. Before the master device LED stops flashing, press the top right button on the master device again with the remote controls close to each other. The master LED will change to steady.
3. Still holding down the master device button, press the same button on the slave.
The slave device LED will flash once to confirm that the code has been stored.
4. Release both buttons.
JCM® EF Remote
- F 290
- C FIX CODE
- B 1,2,3
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
NOVOFERM® M512 Remote
- F 433,92
- C FIX CODE
- B 1,2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
OPEN OUT® L110 Remote
- F 305
- C FIX CODE
- B 1
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
SOMFY® K-EASY OLD Remote
JCM® ET Remote
- F 290
- C FIX CODE
- B 1,2,3
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
JCM® EM Remote
- F 284
- C FIX CODE
- B 1,2,3
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
PUJOL® P15 Remote
- F 290
- C FIX CODE
- B 1,2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
STAGNOLI® VENUS Remote
- F 433,92
- C ROLLING CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
HOW TO SYNCHRONISE STAGNOLI ROLLING CODE REMOTE CONTROLS
STAGNOLI remote control synchronisation can only be performed directly on the receiver itself.
Synchronising the remote control directly on the receiver:
During start-up, LED1 and LED2 will light up for two seconds as follows:
• LED1 on: Variable code programmed.
• LED2 on: Fixed code programmed.
• Both LEDs on: no transmitter in memory.
Once the receiver is powered up, press the synchronisation button (PG) a number of times corresponding to the operation you wish to complete, holding down the button on the last press.
Synchronisation of the first channel on the receiver: Press the synchronisation button (PG) twice and hold. LED1 will blink twice: press the transmitter button you wish to synchronise.
If the new code has been recognised and synchronised correctly, LED1 will emit a long flash.
By holding the synchronisation button (PG), it is possible to synchronise additional transmitters by pressing the buttons (one at a time) on the additional transmitters to be synchronised.
Synchronisation of the second channel on the receiver: Press the synchronisation button (PG) three times and hold. LED1 will blink three times: press the transmitter button you wish to synchronise.
If the new code has been recognised and synchronised correctly, LED1 will emit a long flash.
By holding the synchronisation button (PG), it is possible to synchronise additional transmitters by pressing the buttons (one at a time) on the additional transmitters to be synchronised.
The selected remotes can not be copied with a single JMA remote