FIND YOUR REMOTE

Find your remote and compatable JMA Remote to copy

Legend: Click on the symbols for further information

Frequency

Type of code

  1. Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
  2. Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.

Buttons

Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.

PROCESS:

  1. In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
  2. Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.

If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.

Copy

No copy

FOR: DOORMATIC® AM-300

  • F 300
  • C FIX CODE
  • B 1,2,3
  • AP NO
  • BT Slim / M-FR1 / M-NOVA / M-BT / SR-4V
DOORMATIC® AM-300

See compatible JMA remotes

FOR: DOORMATIC® AZ-433

  • F 433,92
  • C FIX CODE
  • B 1,2,3
  • AP NO
  • BT Slim / M-FR1 / LITE / M-NOVA / M-BT / SR-4V / SR-48
DOORMATIC® AZ-433

See compatible JMA remotes

FOR: DOORMATIC® EURO

  • F 433,92
  • C FIX CODE
  • B 1,2,3
  • AP NO
  • BT Slim / M-FR1 / LITE / M-NOVA / M-BT / SR-4V / SR-48
DOORMATIC® EURO

See compatible JMA remotes

FOR: DOORMATIC® MILENY

  • F 433,92
  • C ROLLING CODE
  • B 1,2,3
  • AP YES
  • BT Slim / M-FR1 / M-NOVA / M-BT / SR-4V / SR-48
DOORMATIC® MILENY

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING DOORMATIC ROLLING CODE REMOTE CONTROLS

In rolling code mode, DOORMATIC receivers can be synchronised either remotely or directly on the receiver.

Remote synchronising procedure

1. Stand near the receiver and press and release the button on the front of the remote control already synchronised in the facility. This button is located under the coloured casing.

The receiver will emit a beep, indicating that it has switched to synchronisation mode.

2. Within 5 seconds, press the button of the device to be synchronised.

The receiver will emit two beeps, indicating that the code has been stored.

Wait for 30 seconds until the receiver emits two beeps, indicating that it has exited the synchronisation mode.

Direct synchronisation procedure on the receiver

1. Open the receiver and locate a pushbutton between two LEDS on a circuit board.

The red LED lights up briefly and turns off. Then the green LED lights up. This indicates that the receiver is in synchronisation mode.

2. Press the button of the desired channel on the remote control to be synchronised.

The receiver will store the code.

Wait for 30 seconds until the receiver emits two beeps, indicating that it has exited the synchronisation mode.

ATTENTION

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices. In this case only the installer will be able to synchronise any new remote controls.