Legend: Click on the symbols for further information

Frequency

Type of code

  1. Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
  2. Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.

Buttons

Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.

PROCESS:

  1. In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
  2. Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.

If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.

Copy

No copy

AERF® TMP-2 Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 2
  • AP YES
  • M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
AERF® TMP-2

Synchronising intructions

Print

SYNCHRONISING AERF ROLLING CODE REMOTE CONTROLS

The JCM rolling code remote control synchronisation procedure is identical for all models, including customised models, except the 868 MHz.

There are two synchronisation procedures for these devices.

Remote synchronisation procedure using the original remote control

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the remote control already synchronised in the facility. If there is no rear button, press all the buttons on the original device at once.

The receiver will emit a beep, indicating that it has switched to synchronisation mode.

2. Within 10 seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

3. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

APRIMATIC® TR Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 2,4
  • AP YES
  • M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
APRIMATIC® TR

Synchronising intructions

Print

SYNCHRONISING APRIMATIC ROLLING CODE REMOTE CONTROLS

Direct synchronisation procedure on the receiver

1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".

2. Press the button or turn on the switch.

The receiver will emit a long beep and the LED will light up. From this point, follow the previous procedure from step 2 above.

Synchronising the APRIMATIC TR remote control

1. Stand near the receiver and press all the emission keys of the device already synchronised in the facility.

The receiver will emit a continuous beep.

2. Press the synch button of the duplicated device.

3. Then press any key of the duplicated device.

The LED and buzzer will pause briefly and then resume, confirming that the remote control is now synchronised.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

AERF® TMP-1 Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 3
  • AP YES
  • M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
AERF® TMP-1

Synchronising intructions

Print

SYNCHRONISING AERF ROLLING CODE REMOTE CONTROLS

The JCM rolling code remote control synchronisation procedure is identical for all models, including customised models, except the 868 MHz.

There are two synchronisation procedures for these devices.

Remote synchronisation procedure using the original remote control

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the remote control already synchronised in the facility. If there is no rear button, press all the buttons on the original device at once.

The receiver will emit a beep, indicating that it has switched to synchronisation mode.

2. Within 10 seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

3. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

CASIT® MPSTFE Remote

Remove Remote
  • F 433,92
  • C FIX CODE
  • B 2,4
  • AP NO
  • M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
CASIT® MPSTFE

APRIMATIC® TS Remote

Remove Remote
  • F 306
  • C FIX CODE
  • B 2
  • AP NO
  • M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
APRIMATIC® TS

LEB® TPWS Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 3
  • AP NO
LEB® TPWS

AERF® ST Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 1,2
  • AP YES
  • M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
AERF® ST

Synchronising intructions

Print

SYNCHRONISING AERF ROLLING CODE REMOTE CONTROLS

The JCM rolling code remote control synchronisation procedure is identical for all models, including customised models, except the 868 MHz.

There are two synchronisation procedures for these devices.

Remote synchronisation procedure using the original remote control

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the remote control already synchronised in the facility. If there is no rear button, press all the buttons on the original device at once.

The receiver will emit a beep, indicating that it has switched to synchronisation mode.

2. Within 10 seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

3. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

AERF® Terra Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 3
  • AP YES
  • M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
AERF® Terra

Synchronising intructions

Print

SYNCHRONISING AERF ROLLING CODE REMOTE CONTROLS

The JCM rolling code remote control synchronisation procedure is identical for all models, including customised models, except the 868 MHz.

There are two synchronisation procedures for these devices.

Remote synchronisation procedure using the original remote control

1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the remote control already synchronised in the facility. If there is no rear button, press all the buttons on the original device at once.

The receiver will emit a beep, indicating that it has switched to synchronisation mode.

2. Within 10 seconds of the beep, press the button on the device to be synchronised.

The receiver will emit another short beep to indicate that the remote control has been synchronised.

If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.

3. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.

V2® PHOENIX Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 4
  • AP NO
  • M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
V2® PHOENIX

Synchronising intructions

Print

SYNCHRONISING V2 ROLLING CODE REMOTE CONTROLS

V2 remote controls can be synchronised either remotely or directly on the receiver.

Remote synchronising procedure

1. Press buttons 1 and 2 on the remote control to be synchronised simultaneously for approximately 10 seconds.

2. Release.

3. Within 5 seconds, press any other button on the device to be synchronised.

4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.

The code has been stored.

Since this option is not enabled on all models we recommend the following procedure.

Direct synchronisation procedure on the receiver

1. Open the receiver and locate the small SW1 button.

2. Press until the receiver LED lights up.

3. Within 5 seconds, press the button on the remote control to be synchronised and hold until the receiver LED blinks.

4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.

The code has been stored.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

V2® PHOX Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 2,4
  • AP NO
  • M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
V2® PHOX

Synchronising intructions

Print

SYNCHRONISING V2 ROLLING CODE REMOTE CONTROLS

V2 remote controls can be synchronised either remotely or directly on the receiver.

Remote synchronising procedure

1. Press buttons 1 and 2 on the remote control to be synchronised simultaneously for approximately 10 seconds.

2. Release.

3. Within 5 seconds, press any other button on the device to be synchronised.

4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.

The code has been stored.

Since this option is not enabled on all models we recommend the following procedure.

Direct synchronisation procedure on the receiver

1. Open the receiver and locate the small SW1 button.

2. Press until the receiver LED lights up.

3. Within 5 seconds, press the button on the remote control to be synchronised and hold until the receiver LED blinks.

4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.

The code has been stored.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

LEB® TMW Remote

Remove Remote
  • F 433,92
  • C FIX CODE
  • B 4
  • AP NO
  • M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
LEB® TMW

V2® Match Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 4
  • AP NO
  • M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
V2® Match

Synchronising intructions

Print

SYNCHRONISING V2 ROLLING CODE REMOTE CONTROLS

V2 remote controls can be synchronised either remotely or directly on the receiver.

Remote synchronising procedure

1. Press buttons 1 and 2 on the remote control to be synchronised simultaneously for approximately 10 seconds.

2. Release.

3. Within 5 seconds, press any other button on the device to be synchronised.

4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.

The code has been stored.

Since this option is not enabled on all models we recommend the following procedure.

Direct synchronisation procedure on the receiver

1. Open the receiver and locate the small SW1 button.

2. Press until the receiver LED lights up.

3. Within 5 seconds, press the button on the remote control to be synchronised and hold until the receiver LED blinks.

4. The receiver LED will turn off after a few seconds, indicating that the unit has exited synchronisation mode.

The code has been stored.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

CASIT® MTE Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 2,4
  • AP NO
  • M-BT Biometric / BT Slim / M-NOVA PRO / M-BT Advance
CASIT® MTE

CASIT® TXS Remote

Remove Remote
  • F 433,92
  • C FIX CODE
  • B 1,2,3,4,6
  • AP NO
  • M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
CASIT® TXS

CASIT® MPSTFRC Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 2,4
  • AP NO
CASIT® MPSTFRC

LEB® TCP Remote

Remove Remote
  • F 433,92
  • C FIX CODE
  • B 2
  • AP NO
  • M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
LEB® TCP

LEB® TRK Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 4
  • AP NO
LEB® TRK

APRIMATIC® TX4S Remote

Remove Remote
  • F 433,92
  • C ROLLING CODE
  • B 4
  • AP YES
  • M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
APRIMATIC® TX4S

Synchronising intructions

Print

SYNCHRONISING APRIMATIC TXM ROLLING CODE REMOTE CONTROLS

Remote synchronisation procedure for the APRIMATIC TXM remote control

1. Stand near the receiver and press all the emission keys of the device already synchronised in the facility.

The receiver will emit a beep and the LED will flash.

2. Press the synch button of the duplicated device.

The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.

3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the original or duplicated remote control.

The LED and buzzer will turn off.

Direct synchronisation procedure for the APRIMATIC TXM remote control

1. Open the receiver and press the small button located near the LED for 2 seconds.

The receiver LED will flash

2. Press the synch button of the duplicated device.

The beep will pause and the LED will remain steady for a moment to confirm that it has received the valid code.

3. Wait 30 seconds to exit the synchronisation mode or press the synch or copy button of the master remote control.

The LED and buzzer will turn off.

Observations

If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.

DOORMATIC® AZ-433 Remote

Remove Remote
  • F 433,92
  • C FIX CODE
  • B 1,2,3
  • AP NO
  • M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
DOORMATIC® AZ-433

DOORMATIC® EURO Remote

Remove Remote
  • F 433,92
  • C FIX CODE
  • B 1,2,3
  • AP NO
  • M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
DOORMATIC® EURO

The selected remotes can not be copied with a single JMA remote