Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
PORTAMATIC® MPSA Remote
- F 289
- C FIX CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
CASIT® MTE Remote
CHAMBERLAIN 2.0® 892MAX Remote
SYNCHRONISING LIFT MASTER ROLLING CODE REMOTE CONTROLS
The Lift Master remote control can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver
1. Press the button on the remote control and hold.
2. Press and release the Learn button for channel A on the receiver.
3. The control LED will flash once.
4. Release the remote control button.
If you release the remote control button before the control LED flashes the receiver will not accept the code.
Repeat this procedure for any other devices you wish to add.
If you are using a second door, select another button on the remote control and repeat the steps for channel B.
ROSSI® CT Remote
HOW TO SYNCHRONISE ROSSI ROLLING CODE REMOTE CONTROLS
ROSSI remote control synchronisation can only be performed directly on the receiver itself.
Synchronising the remote control directly on the receiver
1. Hold the button on the receiver. The red LED will remain lit.
2. Hold down the desired button on the JMA remote control until the LED light on the receiver goes out.
3. Release the button on the JMA remote control. The remote control has been synchronised.
4. Repeat the process for the other buttons.
SOMMER® 4020 Remote
- F 868,3
- C ROLLING CODE
- B 4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING SOMMER ROLLING CODE REMOTE CONTROLS
SOMMER remote control can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver
1. Press button B on the receiver
a. Once for channel 1. LED (C1) will light up.
b. Twice for channel 2. LED (C2) will light up.
The receiver will exit synchronisation mode if no code is transmitted during a period of 10 seconds.
To exit synchronisation mode, press key B several times until all LEDs have turned off.
2. Press the desired button (D) on the remote control. The transmitter will send the radio code to the receiver.
The LED for the selected channel will flash and switch off.
Repeat Steps 1 and 2 to synchronise additional transmitters with this receiver.
B&B® EMY C Remote
PECCININ® 3C Remote
HOW TO SYNCHRONISE PECCINI ROLLING CODE REMOTE CONTROLS
PECCINI remote controls can only be synchronised directly on the receiver.
Synchronising the remote control directly on the receiver
1. Press the record button (PCB) for one second and release. The red LED (LD1) on the board will light up.
2. Press the button on the remote control to record the desired channel.
3. The LED (LD1) on the board will flash, awaiting confirmation.
4. If you only want one button, confirm it.
5. If you want two buttons, confirm with the second of your choice.
6. If you want four buttons, repeat steps 1 to 5 with the remaining buttons.
PROEM® ERC4/C27 Remote
LIFT MASTER 2.0® 951EV Remote
- F 310,315,390
- C ROLLING CODE
- B 1
- AP NO
- M-BT Biometric / BT Slim / M-NOVA PRO / M-BT Advance
SYNCHRONISING LIFT MASTER ROLLING CODE REMOTE CONTROLS
The Lift Master remote control can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver
1. Press the button on the remote control and hold.
2. Press and release the Learn button for channel A on the receiver.
3. The control LED will flash once.
4. Release the remote control button.
If you release the remote control button before the control LED flashes the receiver will not accept the code.
Repeat this procedure for any other devices you wish to add.
If you are using a second door, select another button on the remote control and repeat the steps for channel B.
PROEM® ERC4/ACS Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING SOMFY ROLLING CODE REMOTE CONTROLS
SOMFY remote control can only be synchronised directly on the external receiver and remotely on the integrated shutter receiver. A distinction must be made between SOMFY and TELIS remote controls.
Synchronisation procedure on the receiver
External receiver
1. Press and hold the \"Prog\" button on the receiver for 2 seconds. The red LED on the receiver will remain lit.
Internal receiver (Telis)
1. Press and hold the up and down buttons on the Telis remote control for 2 seconds. The red LED on the receiver will remain lit.
Keytis remote control
2. Press the button of the device to be synchronised. The LED on the receiver will flash.
3. Wait until the LED turns off.
Telis 1RTS remote control
2. Press the rear button on the remote control for half a second. The LED on the receiver will flash.
3. Wait until the LED turns off.
Telis 4 RTS remote control
2. Press the channel selection button until the LED for the desired channel lights up.
3. Press the rear button on the remote control for half a second. The LED on the receiver will flash.
4. Wait until the LED turns off.
PUJOL® PJ Remote
The selected remotes can not be copied with a single JMA remote