Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
MERLIN® M832 Remote
COBRA® 5557 Remote
- F 312
- C FIX CODE
- B 1,2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
PRASTEL® KMFT 306 Remote
- F 306
- C FIX CODE
- B 1,2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
ALLMATIC® BRO.OVER Remote
- F 433,92
- C ROLLING CODE
- B 3
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING BENINCA ROLLING CODE REMOTE CONTROLS
Remote synchronisation procedure for the BENINCA remote control
1. Stand near the receiver and press the already synchronised hidden transmitter key.
2. Within 5 seconds press the key on the already synchronised remote control that corresponds to the channel to be associated with the new device.
3. Within 5 seconds, press the key of the new device to be associated with the channel selected in step 2.
The receiver will memorise the new transmitter and exit synchronisation mode immediately.
Direct synchronisation procedure for the BENINCA remote control
1. Open the receiver and briefly press the P button.
The red LED on the receiver will light up for 3 seconds, turn off for 1 second and light up for a further 5 seconds.
2. While the red LED is lit up, press the transmitter button that you want to synchronise with channel 1.
Other transmitters can also be entered. You only have to press a key before 5 seconds elapse since the previous device was synchronised.
3. Once finished, wait 5 seconds until the receiver exits synchronisation mode.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
SOMMER® 4020 Remote
- F 868,3
- C ROLLING CODE
- B 4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING SOMMER ROLLING CODE REMOTE CONTROLS
SOMMER remote control can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver
1. Press button B on the receiver
a. Once for channel 1. LED (C1) will light up.
b. Twice for channel 2. LED (C2) will light up.
The receiver will exit synchronisation mode if no code is transmitted during a period of 10 seconds.
To exit synchronisation mode, press key B several times until all LEDs have turned off.
2. Press the desired button (D) on the remote control. The transmitter will send the radio code to the receiver.
The LED for the selected channel will flash and switch off.
Repeat Steps 1 and 2 to synchronise additional transmitters with this receiver.
NORMSTAHL® T40 Remote
BFT® MITTOM Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SYNCHRONISING BFT ROLLING CODE REMOTE CONTROLS
The receivers of these models enable remote or direct synchronisation.
Remote synchronisation procedure for the BFT MITTO remote control
1. Stand near the receiver and press the hidden button at the rear of the BFT original remote control for 2 seconds.
2. Press the left button on the front of the original remote control for 2 seconds.
3. Press the synch button on the rear of the device to be synchronised.
4. Finally, press the first button on the device to be synchronised.
Remote synchronisation procedure for the BFT TRC or MITTO remote control
1. Open the receiver and locate the SW-1 and SW-2 buttons. Press the first (SW-1).
A flashing LED should light up in the receiver.
2. Open the battery cover of the already synchronised remote control or the one you have copied and press the button inside.
The receiver light should change to steady.
3. Press the button of the device to be synchronised.
The light on the receiver will return to flashing and turn off after 30 seconds, indicating that the synchronisation process has finished.
Observations
If the procedure fails, it may mean that the receiver memory is full and impedes synchronisation of new devices without the installer\'s permission.
HORMANN® HSBS Remote
The selected remotes can not be copied with a single JMA remote