Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
HORMANN® DHM 27015 Remote
MOTORLIFT® 433EML Remote
- F 433,92
- C FIX CODE
- B 1,3
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
LIFT MASTER® 84335E/EML Remote
- F 433,92
- C ROLLING CODE
- B 3
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING LIFT MASTER ROLLING CODE REMOTE CONTROLS
The Lift Master remote control can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver
1. Press the button on the remote control and hold.
2. Press and release the Learn button for channel A on the receiver.
3. The control LED will flash once.
4. Release the remote control button.
If you release the remote control button before the control LED flashes the receiver will not accept the code.
Repeat this procedure for any other devices you wish to add.
If you are using a second door, select another button on the remote control and repeat the steps for channel B.
JCM® ET Remote
- F 290
- C FIX CODE
- B 1,2,3
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V
PORTAMATIC® MPSA Remote
- F 289
- C FIX CODE
- B 2
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
MHOUSE® MOOVO Remote
- F 433,92
- C ROLLING CODE
- B 4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING MHOUSE ROLLING CODE REMOTE CONTROLS
MHOUSE remote controls can be synchronised either directly on the receiver or remotely using a remote control already synchronised with the receiver.
Remote synchronisation procedure (identical to procedure for NICE, Smilo and Flo-R devices)
1. Press and hold the button on the device you wish to synchronise for at least 5 seconds and then release.
2. Slowly press the button on the previously-synchronised remote control 3 times.
3. Slowly press the button on the device to be synchronised once.
Direct synchronisation procedure on the receiver
1. Press button P1 on the receiver and hold for at least 3 seconds.
2. Release the button when LED P1 lights up.
3. You have 10 seconds to press any button on the device to be synchronised for at least 2 seconds. LED P1 will flash 3 times if synchronisation has been performed successfully.
4. If you wish to synchronise additional remote controls, repeat step 2 within 10 seconds or the receiver will automatically exit synchronisation mode.
SEAV® BE SMART S2 Remote
- F 433,92
- C FIX CODE
- B 2,4
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
ROSSI® CT Remote
HOW TO SYNCHRONISE ROSSI ROLLING CODE REMOTE CONTROLS
ROSSI remote control synchronisation can only be performed directly on the receiver itself.
Synchronising the remote control directly on the receiver
1. Hold the button on the receiver. The red LED will remain lit.
2. Hold down the desired button on the JMA remote control until the LED light on the receiver goes out.
3. Release the button on the JMA remote control. The remote control has been synchronised.
4. Repeat the process for the other buttons.
FORSA® BUTTERFLY Remote
- F 433,92
- C FIX CODE
- B 1,2,3
- AP NO
- M-BT Biometric / BT Slim / M-FR1 / LITE / M-NOVA PRO / M-BT Advance / SR-4V / SR-48
SKY MASTER® MHZ Remote
- F 433,92
- C ROLLING CODE
- B 2,4
- AP YES
- M-BT Biometric / BT Slim / M-FR1 / M-NOVA PRO / M-BT Advance
SYNCHRONISING SKYMASTER ROLLING CODE REMOTE CONTROLS
SKYMASTER remote controls can only be synchronised directly on the receiver. The process is as follows.
Synchronisation procedure on the receiver
1. Press the CODE button once.
The red LED will begin the flash.
2. Press the button on the remote control to be synchronised twice.
The red LED will change to steady and then turn off.
3. Repeat the operation for every button (channel) and every device you wish to synchronise.
If the remote control being synchronised is the first one, you will have to delete the memory as follows:
1. Press and hold the CODE button for 8 seconds during which the LED will remain steady
2. The red LED will turn of and the memory will be deleted.
The selected remotes can not be copied with a single JMA remote