JMA M-FR1 remote control

+34 943 79 30 00

sat@jma.es

M-FR1 Remote

THE MAXIMUM REMOTES DUPLICATING CAPACITY ON THE MARKET

We are expanding our range of compatible remote controls for garage doors and access barriers with the new M Series.

We are adding the M-FR1, a remote control capable of automatically and wirelessly duplicating the frequency and code.

- Duplicate 95% of fixed codes and over 40 rolling code brands onto any of the buttons.

- Wireless code and frequency capture with no need for adjustments. Each button uses different codes and frequencies.

- Operating frequency: 433-868 Mhz.

INSTANT DUPLICATION

Duplicate in two simple steps. 1. Remote control preparation. 2. Transmission of information from the original remote control.

4 REMOTE CONTROLS IN 1

Duplicate four remote controls on a single JMA remote control

THE ROLLING CODE REMOTES THAT CAN COPY

It copies 95% of fixed codes in the market

Play

COPYING 2 PACKET ROLLING CODE WITHOUT RECORDING DATA PACKET

1. Hold buttons 1 and 2 on the JMA remote control simultaneously for 5 seconds until the red LED flashes.

2. Release and wait for it to switch off.

3. Press the button on the JMA remote control over which you want to copy the original remote control.

4. The red LED will remain lit.

5. Place the two remotes facing each other on the right-hand side of the JMA remote on a flat non-metallic surface at a distance of less than 1 cm.

6. Press the original remote control until the LED on the JMA remote turns green and release.

7. Wait for the LED to turn red again.

8. Press the same button on the original remote control to send the second data packet.

9. The JMA remote control will remain green for a few seconds until all the information is saved, when the remote will switch off.

To check that the remote has been copied as a rolling code, the LED should go red when pressing the copied button. If it goes green, it has been captured as a fixed code.

•If the JMA remote control flashes red:

The remote was read incorrectly. You will need to start again.

•If the JMA remote control flashes green:

The remote has been captured as an unverifiable fixed code. You will need to start again.

FREQUENCY ACCEPTED BY THIS REMOTE CONTROL

•From 280Mhz to 360Mhz (outside the European Union)

•From 380Mhz to 400Mhz (outside the European Union)

•433.92Mhz

•868Mhz

READ MORE

Play

COPYING FIXED CODES

1. Hold buttons 1 and 2 on the JMA remote control simultaneously for 5 seconds until the red LED flashes.

2. Release and wait for it to switch off.

3. Press the button on the JMA remote control over which you want to copy the original remote control.

4. The red LED will remain lit.

5. Place the two remotes facing each other on the right-hand side of the JMA remote on a flat non-metallic surface at a distance of less than 1 cm.

6. Press the original remote control until the LED on the JMA remote turns green.

7. The JMA remote control will remain green for a few seconds until all the information is saved, when the remote will switch off.

•If the JMA remote control flashes red:

The remote was read incorrectly. You will need to start again.

•If the JMA remote control flashes green:

If the remote is a Multi-frequency, Mastercode or long code: the remote may flash green, the remote may have been copied correctly. Try it on the door.

FREQUENCY ACCEPTED BY THIS REMOTE CONTROL

•From 280Mhz to 360Mhz (outside the European Union)

•From 380Mhz to 400Mhz (outside the European Union)

•433.92Mhz

•868Mhz

READ MORE

Play

COPYING 1 PACKET ROLLING CODE

1. Hold buttons 1 and 2 on the JMA remote control simultaneously for 5 seconds until the red LED flashes.

2. Release and wait for it to switch off.

3. Press the button on the JMA remote control over which you want to copy the original remote control.

4. The red LED will remain lit.

5. Place the two remotes facing each other on the right-hand side of the JMA remote on a flat non-metallic surface at a distance of less than 1 cm.

6. Press the original remote control until the LED on the JMA remote turns green.

7. The JMA remote control will remain green for a few seconds until all the information is saved, when the remote will switch off.

To check that the remote has been copied as a rolling code, the LED should go red when pressing the copied button. If it goes green, it has been captured as a fixed code.

•If the JMA remote control flashes red:

The remote was read incorrectly. You will need to start again.

•If the JMA remote control flashes green:

The remote has been captured as an unverifiable fixed code. You will need to start again.

FREQUENCY ACCEPTED BY THIS REMOTE CONTROL

•From 280Mhz to 360Mhz (outside the European Union)

•From 380Mhz to 400Mhz (outside the European Union)

•433.92Mhz

•868Mhz

READ MORE

Play

COPYING 2 PACKET ROLLING CODE WITH RECORD BUTTON

1. Hold buttons 1 and 2 on the JMA remote control simultaneously for 5 seconds until the red LED flashes.

2. Release and wait for it to switch off.

3. Press the button on the JMA remote control over which you want to copy the original remote control.

4. The red LED will remain lit.

5. Place the two remotes facing each other on the right-hand side of the JMA remote on a flat non-metallic surface at a distance of less than 1 cm.

6. Press the original remote control until the LED on the JMA remote turns green and release.

7.Wait for the LED to turn red again.

8. Press the record button on the original remote control to send the second data packet.

If the original remote is BFT or ERREKA, the recording data packet is sent by pressing the hidden button or buttons 1 and 2 on the original remote simultaneously.

If the original remote is FAAC Master, the recording data packet is sent as follows: Away from the M-FR1 remote, press buttons 1 and 2 (in diagonal) on the original remote simultaneously until the LED on the original remote starts flashing. With the LED still flashing, move the original remote close to the M-FR1 remote and press the button on the original remote that you want to copy.

9. The JMA remote control will remain green for a few seconds until all the information is saved, when the remote will switch off.

To check that the remote has been copied as a rolling code, the LED should go red when pressing the copied button. If it goes green, it has been captured as a fixed code.

•If the JMA remote control flashes red:

The remote was read incorrectly. You will need to start again.

•If the JMA remote control flashes green:

The remote has been captured as an unverifiable fixed code. You will need to start again.

FREQUENCY ACCEPTED BY THIS REMOTE CONTROL

•From 280Mhz to 360Mhz (outside the European Union)

•From 380Mhz to 400Mhz (outside the European Union)

•433.92Mhz

•868Mhz

READ MORE

This website uses its own cookies and cookies from third parties in order to optimise your browsing experience, better meet your needs, and perform analytical tasks. By continuing to browse you accept our Cookies Policy.ACCEPT